Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Utiliza los dedos para empujar las dos lengüetas de liberación de la batería y sácala del ordenador.
-
-
-
Retira los cuatro tornillos Phillips idénticos de 3,4 mm de la puerta de la memoria. Estos tornillos tienen cabezas de 4 mm de diámetro en lugar de las cabezas de 3 mm de los tornillos del cuerpo.
-
-
-
Retira los tres tornillos Phillips del compartimento de la batería, cerca del pestillo. Apple tuvo la amabilidad de inclinar estos tornillos en un ligero ángulo para facilitar su extracción. En el A1261 estos tornillos tienen cabezas de 4 mm de diámetro en lugar de las cabezas de 3 mm en los tornillos del cuerpo.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three screws:
-
Two black 4 mm T6 Torx screws on either side of the SuperDrive.
-
One 8.7 mm silver (black in some models) T6 Torx screw at the back of the drive near the speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use one hand to pull back the speaker cable and use your other hand to lift the optical drive up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the ten indicated connectors from the logic board.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the large display data cable to the left and disconnect the small right thermal sensor cable beneath.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single black 4 mm T6 Torx screw securing the clear plastic shield over the right ambient light sensor.
-
Lift the clear plastic shield off the right ambient light sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange Kapton tape securing the left thermal sensor cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following twelve screws:
-
Seven 6.5 mm T6 Torx screws.
-
Two shanked 7.6 mm T6 Torx screws securing the battery connector to the lower case.
-
Three 7.8 mm T6 Torx screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the left side of the logic board and disconnect the multi-colored power connector from the bottom of the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the logic board at the left side and at the thin section near the right fan, and rotate the logic board out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If the right speaker assembly remains attached to the logic board, hold the logic board with one hand and slide the speaker up slightly to free it from the logic board.
-
To properly reassemble your MacBook Pro, you'll have to clean off and replace the thermal compound from the three chips on the underside of the logic board. Use our Applying Thermal Paste Guide to prepare the processor and heat sink surfaces.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables attached to the AirPort Extreme card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single black 4 mm T6 Torx screw from the top right corner of the AirPort Extreme card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the AirPort Extreme card up and slide it out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 7.8 mm silver T6 Torx screws from the top left and bottom right corners of the left speaker assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up on the left speaker assembly and rotate it slightly. It is not possible to entirely remove the speaker yet, as it is still connected to the left I/O board beneath.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the right speaker from the left I/O board. Make sure to pull on the top section of the white connector, not the cable itself.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the right speaker assembly out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two cables attaching the left speaker assembly to the left I/O board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the iSight and inverter cables which are attached with a mild adhesive above the left fan.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five 7.8 mm T6 Torx screws securing the fans to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the heat sink and attached fans out of the computer.
-
Now is a good time to lean the fans back and clean out any dust bunnies from the grill. Also clean any dried thermal paste from the heat sink contact pads.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the ten silver T6 Torx screws securing the display (five on each side). On the right a 9.6 mm screw secures the display data cable, also on the left the screw closest to the inside is 9.6 mm. The others are 7.8 mm.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the display assembly on both sides and lift it up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the Bluetooth assembly out of its slot on the left side of the hard drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two silver T6 Torx screws securing the gray metal retaining bracket to the right side of the hard drive.
-
Lift the gray metal retaining bracket out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the hard drive up from the right side and remove it from the computer. The Bluetooth assembly and orange ribbon cable are still attached to the hard drive and will come out with the hard drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four black 4 mm T6 Torx screws securing the left I/O board to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the right side of the left I/O board and slide it out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange tape covering the right thermal sensor.
-
Use a spudger or your fingernail to pry the right thermal sensor off the lower case.
-
Cancelar: No complete esta guía.
18 personas más completaron esta guía.