Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Usa tus dedos para empujar ambas pestañas de liberación de la batería para separarlas de la batería y levanta la batería para sacarla de la computadora.
-
-
-
Retira los tres tornillos Phillips idénticos de la tapa de la memoria.
-
-
-
Retira los dos tornillos Phillips en el compartimiento de la batería cerca del pestillo.
-
-
-
Levanta la parte posterior del estuche y pasa los dedos por los lados, liberando el estuche a medida que avanza. Una vez que hayas liberado los lados, es posible que tengas que mover la caja hacia arriba y hacia abajo para liberar el frente de la caja superior. Esta etapa puede ser bastante complicada.
-
Sobre el lector de DVD hay 4 pestañas retrasadas que se abren verticalmente.
-
Ten en cuenta que las dos pequeñas lengüetas en el frente izquierdo de la caja superior pueden doblarse mientras retiras la caja superior. Al volver a instalarlos, es posible que debas doblarlos hacia atrás para que encajen en las ranuras de la carcasa inferior.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the display data cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up and remove the orange foil shield near the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.
-
Slide the left ambient light sensor cable to the left and out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the left ambient light sensor cable from above the left fan.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables attached to the Airport Extreme card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single silver Phillips screw located just above the Airport Extreme card.
-
Lift the small silver metal retaining bracket up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back the orange tape on the right side of the Airport Extreme card.
-
Lift the Airport Extreme card up and slide it out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange hard drive ribbon cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange hard drive ribbon from above the ExpressCard cage.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the speaker cable from the front right corner of the left I/O board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 2 screws:
-
One 4.3 mm black T6 Torx screw on the left side of the speaker.
-
One 9.4 mm silver T6 Torx screw on the right side of the speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the left and right speakers out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single silver Phillips screw securing the left ambient light sensor cover to the speaker.
-
Remove the clear plastic ambient light sensor cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry the left ambient light sensor board out of its housing on the left speaker.
-
Cancelar: No complete esta guía.
4 personas más completaron esta guía.