Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Usa tus dedos para empujar ambas pestañas de liberación de la batería para separarlas de la batería y levanta la batería para sacarla de la computadora.
-
-
-
Retira los tres tornillos Phillips idénticos de la tapa de la memoria.
-
-
-
Retira los dos tornillos Phillips en el compartimiento de la batería cerca del pestillo.
-
-
-
Levanta la parte posterior del estuche y pasa los dedos por los lados, liberando el estuche a medida que avanza. Una vez que hayas liberado los lados, es posible que tengas que mover la caja hacia arriba y hacia abajo para liberar el frente de la caja superior. Esta etapa puede ser bastante complicada.
-
Sobre el lector de DVD hay 4 pestañas retrasadas que se abren verticalmente.
-
Ten en cuenta que las dos pequeñas lengüetas en el frente izquierdo de la caja superior pueden doblarse mientras retiras la caja superior. Al volver a instalarlos, es posible que debas doblarlos hacia atrás para que encajen en las ranuras de la carcasa inferior.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the eight indicated connectors from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.
-
Slide the left ambient light sensor cable to the left and out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the silver T6 Torx screw securing the ground loop on the display data cable to the casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single silver T6 Torx screw securing the clear plastic shield over the right ambient light sensor.
-
Lift the clear plastic shield off the right ambient light sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 16 screws, moving cables as necessary:
-
One 4.4 mm black Phillips screw to the right of the RAM slot.
-
Nine 4.7 mm silver T6 Torx screws securing the logic board to the lower case.
-
One 6.2 mm black T6 Torx screw on the right side of the left fan.
-
Five 9.4 mm silver T6 Torx screws securing the left and right fans.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Move the display data cable to the right, removing tape as necessary.
-
Peel up and remove the orange foil shield near the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the iSight and inverter board cables from above the left fan.
-
Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the fan up.
-
Place the fan above the Airport card. It is not necessary to entirely remove the fan from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the right fan up while carefully peeling up the tape which secures the fan to the heat sink.
-
Remove the right fan from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the left side of the logic board and disconnect the multi-colored power cable from the bottom of the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the right thermal sensor cable from the bottom of the logic board near the DVI port.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange Kapton tape covering the right thermal sensor.
-
Use a spudger to pry the right thermal sensor off the lower case.
-
Cancelar: No complete esta guía.
Una persona más ha completado esta guía.