Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Usa tus dedos para empujar ambas pestañas de liberación de la batería para separarlas de la batería y levanta la batería para sacarla de la computadora.
-
-
-
Retira los tres tornillos Phillips idénticos de la tapa de la memoria.
-
-
-
Retira los dos tornillos Phillips en el compartimiento de la batería cerca del pestillo.
-
-
-
Levanta la parte posterior del estuche y pasa los dedos por los lados, liberando el estuche a medida que avanza. Una vez que hayas liberado los lados, es posible que tengas que mover la caja hacia arriba y hacia abajo para liberar el frente de la caja superior. Esta etapa puede ser bastante complicada.
-
Sobre el lector de DVD hay 4 pestañas retrasadas que se abren verticalmente.
-
Ten en cuenta que las dos pequeñas lengüetas en el frente izquierdo de la caja superior pueden doblarse mientras retiras la caja superior. Al volver a instalarlos, es posible que debas doblarlos hacia atrás para que encajen en las ranuras de la carcasa inferior.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws:
-
Two 3.3 mm silver Phillips screws on either side of the SuperDrive.
-
One 4.8 mm black Phillips screw at the top right corner of the drive.
-
The 4.8mm screw may be a T6 Torx
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the eight indicated connectors from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.
-
Slide the left ambient light sensor cable to the left and out of its connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the silver T6 Torx screw securing the ground loop on the display data cable to the casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single silver T6 Torx screw securing the clear plastic shield over the right ambient light sensor.
-
Lift the clear plastic shield off the right ambient light sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 16 screws, moving cables as necessary:
-
One 4.4 mm black Phillips screw to the right of the RAM slot.
-
Nine 4.7 mm silver T6 Torx screws securing the logic board to the lower case.
-
One 6.2 mm black T6 Torx screw on the right side of the left fan.
-
Five 9.4 mm silver T6 Torx screws securing the left and right fans.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Move the display data cable to the right, removing tape as necessary.
-
Peel up and remove the orange foil shield near the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the iSight and inverter board cables from above the left fan.
-
Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the fan up.
-
Place the fan above the Airport card. It is not necessary to entirely remove the fan from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the right fan up while carefully peeling up the tape which secures the fan to the heat sink.
-
Remove the right fan from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the left side of the logic board and disconnect the multi-colored power cable from the bottom of the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the right thermal sensor cable from the bottom of the logic board near the DVI port.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the chip directly out from its connector.
-
Cancelar: No complete esta guía.
53 personas más completaron esta guía.
4 comentarios
Buying the part, it says that thermal paste is needed for installation. Where?
Thermal paste is needed to transfer heat from the Nvidia GPU and the CPUs to the heat spreader bar which is located below the motherboard. It transfers heat from the CPUs to the fans.
The final part says to just follow the steps in reverse order to reassemble--that isn't quite enough information. It is critical *not* to snug or overtighten the memory door screws from step 2. The screws pass to the bottom of the keyboard, and the keyboard is made of a light material that deforms easily. If you overtighten the screws it will bend the keyboard out of shape and the spacebar will not work properly.
After installing the screws on the memory door, then test that the space bar goes down and back up properly. If it doesn't back the screws out and try again. Do not proceed with the rest of reassembly if the keyboard is not working.
I totally second this!