Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Utiliza los dedos para empujar las dos lengüetas de liberación de la batería y sácala del ordenador.
-
-
-
Retira los dos tornillos Phillips de 2,8 mm en el compartimento de la batería cerca del pestillo.
-
-
-
Levanta la parte trasera de la caja y desliza los dedos por los laterales, liberando la caja a medida que avanzas. Una vez que hayas liberado los laterales, es posible que tengas que mover la caja hacia arriba y hacia abajo para liberar la parte delantera de la caja superior (hay algunos clips de plástico ocultos que hay que quitar).
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 4 screws:
-
Two 3.3 mm silver Phillips screws on either side of the SuperDrive.
-
One 4.7 mm silver T6 Torx screw from the top left corner of the drive
-
One 6.2 mm black Phillips screw at the top right corner of the drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the iSight and display data cables from the logic board by sliding the cables out of their connectors, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the eight indicated connectors by placing a spudger beneath each cable and lifting up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the silver T6 Torx screw securing the ground loop in the display data cable to the casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single T6 Torx screw securing the clear plastic shield over the right ambient light sensor.
-
Lift the clear plastic shield off the right ambient light sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 15 screws:
-
One 4.4 mm black Phillips screw to the right of the ram slot.
-
Eight 4.7 mm silver T6 Torx screws securing the logic board to the lower case.
-
One 6.2 mm black T6 Torx screw on the right side of the left fan.
-
Five 9.4 mm silver T6 Torx screws securing the left and right fans.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the fan up.
-
Place the fan above the Airport card. It is not necessary to remove the fan from the computer entirely.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the right fan up and carefully peel up the tape securing the fan to the heat sink as you go.
-
Remove the right fan from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the left side of the logic board and disconnect the gray and black power cable from the bottom of the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two silver T6 Torx screws securing the battery connector to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the large gray and black battery connector cable from the left I/O board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Thread the gray and black power cable beneath the speaker cable, and lift the battery connector out of the computer.
-
Cancelar: No complete esta guía.
2 personas más completaron esta guía.
Un comentario
Used now some of the different MacBook manuals several times.
Yes the manuals are GREAT!
Have two very, very, very minor feedbacks.
1.
I have a few very, very short Phillips screws (about 2.2 mm), but in the manual I do not find such a small size mentioned, so I do not know at which step to use them... not at every single step is the size of the screw/s mentioned.
2.
I printed out the manuals. The colors used for emphasizing a step should be more different.
It is hard (for me) to see which circle is orange and which is red; same for the two blue colors.