Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Utiliza una moneda o un spudger para girar el tornillo de bloqueo de la batería 90 grados en el sentido de las agujas del reloj.
-
-
-
Desatornilla los tres tornillos Phillips espaciados uniformemente a lo largo de la pared posterior del compartimento de la batería.
-
-
-
Retira los 3 tornillos siguientes:
-
Un Phillips#00 de 11 mm en el centro de la caja inferior. (Cabeza: 5 mm de diámetro x 0,75 mm de grosor)
-
Dos Phillips #00 de 14,5 mm (cabeza: 5 mm de diámetro x 0,75 mm de grosor)
-
-
-
-
Retira los siguientes 4 tornillos de la parte posterior del ordenador:
-
Dos Phillips #00 de 11 mm, con mango (2,2 mm de diámetro x 2 mm de longitud) (Cabeza: 3,2 mm de diámetro x 0,5 mm de grosor)
-
Dos Phillips #00 de 7,25 mm, con mango (2 mm de diámetro x 3,75 mm de longitud) (cabeza: 3,2 mm de diámetro x 0,5 mm de grosor)
-
-
Herramienta utilizada en este paso:Plastic Cards$2.99
-
Utiliza una herramienta de apertura de plástico, un crédito de plástico caducado o una tarjeta de grosor similar para hacer palanca en la carcasa superior, comenzando en la esquina superior izquierda y trabajando alrededor de la parte frontal del ordenador.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the left 3 mm and right 8 mm (right screw is unnecessary to remove on some models)
-
One 3.25mm Phillips #000 (Head: 4mm dia. x .5mm thick)
-
One 8.5mm Phillips #000 (Head: 4mm dia. x .75mm thick
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently de-route the speaker cable from the left I/O frame.
-
Use a spudger to lift the left speaker out of its housing. Grasp it with your fingers and move it out of the way.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the MagSafe board connector from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three screws securing the left I/O frame:
-
Two 7.5 mm Phillips screws from the top and bottom end of the left I/O frame.
-
One 9 mm Phillips from the middle of the left I/O frame.
-
On some models, all three screws may be the same size.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
The MagSafe board is now free of all connections and can be detached freely from the logic board.
-
Using your fingers, pull out the MagSafe board.
-
Cancelar: No complete esta guía.
136 personas más completaron esta guía.
4 comentarios
Since the use of magnetic tipped drivers is probably NOT recommended, I'd keep some partially dried rubber cement or similar (snotty consistency) around to stick screws onto the driver tips. It makes guiding the screw into cramped areas much easier and rubs right off afterwards.
I believe every single screw that I unscrewed required a Phillips #000 (instead of #0 or #00). Could just be my model. Great guide otherwise.
Following this guide, I fixed the balanced audio on my laptop. I appreciate your thorough instruction. My goal is to open a repair shop, but in order to do that, I must learn a lot from you. gartic phone
Bahçeşehir Konut Projeleri thanks for helpfull writing. this article very important and true.