Saltar al contenido principal
  1. Antes de continuar, apaga tu MacBook. Cierra la pantalla y colócalo en una superficie suave con la parte superior hacia abajo.
    • Antes de continuar, apaga tu MacBook. Cierra la pantalla y colócalo en una superficie suave con la parte superior hacia abajo.

    • Usa un destornillador P5 Pentalobe para quitar los diez tornillos que sujetan la carcasa. Los tornillos tienen las siguientes medidas:

    • Dos tornillos Pentalobe P5 de 9 mm

    • Ocho tornillos Pentalobe P5 de 2,6 mm

  2. Introduce tus dedos entre la pantalla y la carcasa y tira hacia arriba para separar la carcasa.
    • Introduce tus dedos entre la pantalla y la carcasa y tira hacia arriba para separar la carcasa.

    • Retira la carcasa y déjala a un lado.

  3. Como precaución contra descargas o descargas accidentales, desconecte el conector de la batería de la placa lógica. Agarre la lengüeta de plástico transparente unida al conector de la batería y tire de ella hacia el borde frontal del Air para desconectar la batería de la placa lógica.
    • Como precaución contra descargas o descargas accidentales, desconecte el conector de la batería de la placa lógica.

    • Agarre la lengüeta de plástico transparente unida al conector de la batería y tire de ella hacia el borde frontal del Air para desconectar la batería de la placa lógica.

    • Asegúrese de tirar del conector horizontalmente hacia la batería, y no hacia arriba desde el Air, o puede dañar el enchufe de la placa lógica.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.
    • Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Carefully peel the I/O board cable from the top of the fan.
    • Carefully peel the I/O board cable from the top of the fan.

  6. Este paso está sin traducir. Ayuda a traducirlo

    The following connector has an especially deep socket. Use care when disconnecting it. While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help "walk" it out of its socket.
    • The following connector has an especially deep socket. Use care when disconnecting it.

    • While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help "walk" it out of its socket.

    • Remove the I/O board cable.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Peel the rubber gasket off the adhesive on the top of the fan.
    • Peel the rubber gasket off the adhesive on the top of the fan.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Remove the following three screws securing the fan to the upper case:
    • Remove the following three screws securing the fan to the upper case:

    • One 3.6 mm T5 Torx screw

    • One 2.7 mm T5 Torx screw

    • One 3.6 mm T5 Torx screw with a short head

  10. Saque el ventilador de la carcasa superior y tire con cuidado del cable plano del ventilador fuera de su zócalo mientras lo retira del Air.
    • Saque el ventilador de la carcasa superior y tire con cuidado del cable plano del ventilador fuera de su zócalo mientras lo retira del Air.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the I/O board by pulling the power cable away from its socket on the logic board.
    • Disconnect the I/O board by pulling the power cable away from its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the right edge of the Air.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Pull the camera cable parallel to the face of the I/O board toward the hinge of the Air to disconnect it from its socket, using the tip of a spudger to help push the connector out of its socket.
    • Pull the camera cable parallel to the face of the I/O board toward the hinge of the Air to disconnect it from its socket, using the tip of a spudger to help push the connector out of its socket.

    • Do not lift upward on this cable as you disconnect it, as its socket may break off the logic board.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.
    • Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.

    • Pry up from beneath the wires.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Use the tip of a spudger to flip up the retaining flap securing the microphone ribbon cable to the I/O board. Use the tip of a spudger to remove the volume button ribbon cable from its ZIF connector on the I/O board.
    • Use the tip of a spudger to flip up the retaining flap securing the microphone ribbon cable to the I/O board.

    • Use the tip of a spudger to remove the volume button ribbon cable from its ZIF connector on the I/O board.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Remove the single 4.0 mm T5 Torx screw securing the I/O board to the upper case.
    • Remove the single 4.0 mm T5 Torx screw securing the I/O board to the upper case.

  16. Este paso está sin traducir. Ayuda a traducirlo

    Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.
    • Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.

Linea de Meta

36 personas más completaron esta guía.

Equipo

iFixit Miembro de iFixit

Community

138 Miembros

15,576 Guías creadas

4 comentarios

Where can I buy the 2012 I/O board?

Andrew - Contestar

I bought a used I/O board on ebay for $30. Replacing the i/o board solved my problem with the "fan stack" heat sensor which had been unreadable and causing the computer to run very slowly and the fan to run full speed. It was listed like this:

2012 13" MacBook Air MagSafe II DC audio I/O Power Board A1466

fornext - Contestar

HELP NEEDED PLEASE !

While removing the Board I torn apart the pièce at the end of the cable (linked to side) on the l'est of the lasr image. What is it and Howard Can I remplace it ?

Sasha Baba - Contestar

The is a connection that is near the middle outside of the board (near the wifi card) and it looks similar to the I/O connection. Would anyone be able to identify what that connection is and what it is for. I have a 2012 MBA and I wondered if it is a PCIe connection that is unused???

Andy - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 32

Ultimos 30 días: 137

Todo El Tiempo: 27,617