Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Retira los siguientes 10 tornillos:
-
Dos tornillos Pentalobe de 5 Puntos de 8 mm
-
Ocho tornillos Pentalobe de 5 Puntos de 2.5 mm
-
-
-
Usa el extremo plano de un spudger para levantar ambos lados cortos del conector de la batería hacia arriba para desconectarlo de su zócalo en la placa lógica.
-
Dobla el cable de la batería un poco lejos de la placa lógica para que el conector no se doble hacia atrás accidentalmente y haga contacto con su zócalo.
-
-
-
-
Retira los siguientes cinco tornillos que fijan la batería a la carcasa superior:
-
Dos tornillos Torx T5 de 5,2 mm
-
Un tornillo Torx T5 de 6 mm
-
Dos tornillos Torx T5 de 2,6 mm
-
-
-
Levanta la batería por el borde más cercano a la placa lógica y extráigala de la carcasa superior.
-
Cárgalo al 100% y sigue cargándolo durante al menos 2 horas más. A continuación, desenchúfalo y utilízalo normalmente para agotar la batería. Cuando veas el aviso de batería baja, guarda tu trabajo y mantén el portátil encendido hasta que entre en reposo por batería baja.
-
Espere al menos 5 horas y, a continuación, cargue el portátil ininterrumpidamente al 100%.
-
Si notas algún comportamiento inusual o problemas después de instalar la nueva batería, es posible que tengas que restablecer el SMC de tu MacBook.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.
-
Gently slide the ribbon cable out of the ZIF connector.
-
Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad's depth sensitivity.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.
-
Use a spudger to flip up the retaining flap.
-
Gently slide the cable out of the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Open the device about 10 degrees.
-
While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.
-
Remove the trackpad from the device.
-
Cancelar: No complete esta guía.
9 personas más completaron esta guía.
3 comentarios
Hi. After my trackpad “click” started failing (it wouldn’t physically feel like a click when pressed and it wouldn’t respond unless you pushed hard and in certain areas) I went through the whole above replacement process with a trackpad I bought off of Amazon. The new trackpad has a better click on the right hand side but the left hand side is not working still.
Could it be that the new trackpad I got also doesn’t work? The reviews on Amazon indicated that the trackpads from this seller sometimes also failed.
Or is there another problem? I noticed there are two black rubber pads (made of a thin foam) that are between the base of the trackpad and the body of the macbook frame, and that in my computer they are worn/frayed. Could this be the problem?
If anyone has any knowledge about this, or advice about how to go about with this repair and trying different things, I would appreciate your help.
I’d love to know the answers to the above questions before I take mine apart!
this was very easy thanks