Repara tus cosas Comunidad Tienda

Logic Board Disconnection

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Introducción

Prerequisite-only guide to disconnect the logic board in a 2019 MacBook Air.

Qué necesitas

  1. Logic Board Disconnection, Disconnect the logic board: paso 1, imagen 1 de 2 Logic Board Disconnection, Disconnect the logic board: paso 1, imagen 2 de 2

    • Use a T3 Torx driver to remove the two 1.4 mm screws securing the trackpad connector bracket.

    • Depending on the condition of your bits, a T4 Torx driver may fit better.

    • Remove the trackpad connector bracket.

    Editar

  2. Logic Board Disconnection: paso 2, imagen 1 de 2 Logic Board Disconnection: paso 2, imagen 2 de 2

    • Use the flat end of a spudger to pry the trackpad cable connector up and out of its socket.

    Editar

  3. Logic Board Disconnection: paso 3, imagen 1 de 3 Logic Board Disconnection: paso 3, imagen 2 de 3 Logic Board Disconnection: paso 3, imagen 3 de 3

    • If the left speaker is already disconnected, skip this step.

    • Slide the tip of a spudger underneath the left speaker cable and pry straight up to disconnect the speaker.

    • With the connector disconnected, slide the flat end of a spudger under the cable to separate the adhesive securing the cable to the logic board.

    Editar

  4. Logic Board Disconnection: paso 4, imagen 1 de 2 Logic Board Disconnection: paso 4, imagen 2 de 2

    • Use a T3 Torx driver to remove the two 1.3 mm screws securing the USB-C port connector bracket.

    • Remove the USB-C connector bracket.

    Editar

  6. Logic Board Disconnection: paso 5, imagen 1 de 2 Logic Board Disconnection: paso 5, imagen 2 de 2

    • Use the flat end of a spudger to pry the USB-C cable connector up and out of its socket on the logic board.

    Editar

  7. Logic Board Disconnection: paso 6, imagen 1 de 3 Logic Board Disconnection: paso 6, imagen 2 de 3 Logic Board Disconnection: paso 6, imagen 3 de 3

    • Use a spudger to lift up the small locking flap on the sound board cable's ZIF connector.

    • Slide the sound board cable out of the ZIF connector.

    Editar

  8. Logic Board Disconnection: paso 7, imagen 1 de 1

    • Peel back the black tape covering the fan cable connector.

    Editar

  9. Logic Board Disconnection: paso 8, imagen 1 de 3 Logic Board Disconnection: paso 8, imagen 2 de 3 Logic Board Disconnection: paso 8, imagen 3 de 3

    • Use the tip of a spudger to lift up the locking flap on the fan cable's ZIF connector.

    • Slide the fan cable out of the ZIF connector.

    Editar

  10. Logic Board Disconnection: paso 9, imagen 1 de 2 Logic Board Disconnection: paso 9, imagen 2 de 2

    • Use a T3 Torx driver to remove the two 1.4 mm screws securing the antenna cable bracket.

    • Remove the antenna cable bracket.

    Editar

  11. Logic Board Disconnection: paso 10, imagen 1 de 3 Logic Board Disconnection: paso 10, imagen 2 de 3 Logic Board Disconnection: paso 10, imagen 3 de 3

    • Insert the point of a spudger under one of the antenna cables close to the connector. Pry straight up to disconnect the cable.

    • Repeat for the other antenna cable.

    Editar

  12. Logic Board Disconnection: paso 11, imagen 1 de 2 Logic Board Disconnection: paso 11, imagen 2 de 2

    • Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector bracket.

    • Remove the display cable connector bracket.

    Editar

  13. Logic Board Disconnection: paso 12, imagen 1 de 2 Logic Board Disconnection: paso 12, imagen 2 de 2

    • Use the flat end of a spudger to pry up the display cable connector.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

Adam O'Camb

Miembro Desde 04/11/15

196,626 Reputación

416 Guías creadas

Insignias: 39

+ 36 más insignias

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 6

Ultimos 30 días: 7

Todo El Tiempo: 122