Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn over the device so that the bottom is facing up. Make sure the hinged side is facing you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Move the right switch towards the right until it clicks in place. You should then see the color red reveal from where the switch was originally.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Now take your left hand and slide the left switch to the left.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Take your free hand and place it on the battery. Gently slide it away from its slot.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the laptop so that now the hinge is facing away from you.
-
Remove the two 2.5 x 4.0 mm Phillips #0 screws from the underside of the laptop.
-
Slide the bottom panel towards you until it stops, and then carefully lift it off.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.0 x 6.0 mm Phillips #0 screws located on the underside of the device.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the laptop right side up and open the lid.
-
Using the spudger and your fingers, get in between the keyboard's edge and lift it up.
-
Carefully lift the keyboard ribbon cable out of the socket it is in.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 2.5 x 6.0 mm Phillips #0 from the center of the device.
-
Close the laptop and place it face down once again.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If a hard disk drive is installed, remove the two 2.5 x 4.0 mm Phillips #0 screws.
-
Slide the hard disk drive out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the eleven 2.5 x 6.0 mm Phillips #0 screws.
-
Remove the three 2.0 x 3.0 mm flat head screws.
-
Remove the 2.5 x 4.0 mm Phillips #0 screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the laptop right side up and open the lid.
-
Disconnect the two ribbon cables from the center.
-
Lift the keyboard bezel (with trackpad) straight up and out.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five ribbon cables on the top of the computer.
-
Gently remove the single cable from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.5 x 3.0 mm Phillips #0 screws on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using your fingers or a spudger, lift the motherboard slightly.
-
Detach the single cable from underneath.
-
Lift the motherboard the rest of the way out.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.0 x 3.2 mm Phillips #0 screws from the fan.
-
Lift the fan straight off the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a flathead screwdriver, turn the beige lock to counterclockwise to unlocked.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.
Equipo
UMass Dartmouth, Team S5-G2, Peak Spring 2018 Miembro de UMass Dartmouth, Team S5-G2, Peak Spring 2018
UMASSD-PEAK-S18S5G2
2 Miembros
5 Guías creadas
Un comentario
süper olmuş eline sağlık çok açıklayıcı ve başarılı olmuş teşekkür ederim
