Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Introducción

Replacing the Cold Water Reserve Arm is a fairly simple task that does not require a large time investment. Even beginners should be able to complete this replacement without the need for outside help.

Qué necesitas

Paso 1 Cold Water Reserve Lid

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cold Water Reserve Lid: paso 1, imagen 1 de 2

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cold Water Reserve Lid: paso 1, imagen 2 de 2

Lift the cold water reserve lid up to reveal its hinge.
Using either the metal spudger or the opening tool, gently pry the plastic out of the metal axle.

Traducir

Paso 2

Repeat the last step on the other hinge, making sure to keep a firm grasp on the lid as it comes off to avoid dropping it.

Traducir

Paso 3 Cup Holder

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cup Holder: paso 3, imagen 1 de 3

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cup Holder: paso 3, imagen 2 de 3

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cup Holder: paso 3, imagen 3 de 3

Press on tab while pulling up on K-cup until you hear a click. Repeat for the remaining tabs. We found using the smallest of the "plastic opening tools" worked wonders.

Traducir

Paso 4

Once all of the tabs have been pressed, the K-Cup should just pop out. After, you just pull the remainder of the K-Cup. You have successfully removed the K-Cup.

Traducir

Paso 5 Top Needle

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Top Needle: paso 5, imagen 1 de 2

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Top Needle: paso 5, imagen 2 de 2

Remove two 9 mm Phillips #1 screws.
Avoid the top needle if at all possible. The needle may cut you and/or penetrate your skin.
The screws are located on the top of where the K-Cup would be.

Traducir

Paso 6

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement: paso 6, imagen 3 de 3

Once you remove the screws, the top cover should come out.
You will then want to remove these screws which are the same size.
The needle is sharp, so be careful.

Traducir

Paso 7

Once you get those removed, you are going to want to pull on the hose until it pops off.
Once the hose comes off, the needle will fall out by itself.
Be careful when picking up the needle as the needle is sharp.

Traducir

Paso 8 Cold Water Reserve Arm

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cold Water Reserve Arm: paso 8, imagen 1 de 3

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cold Water Reserve Arm: paso 8, imagen 2 de 3

Keurig K10 MINI PLUS Cold Water Reserve Arm Replacement, Cold Water Reserve Arm: paso 8, imagen 3 de 3

Remove two 14 mm Phillips #2 screws.
Remove two 12 mm Phillips #2 screws.
Lift the arm off the assembly. This will reveal the tank hole as shown.
It is recommended that you clog the tank hole with a napkin or something similar in order to prevent small parts from falling into the heating element.

Traducir

Paso 9

Remove two 9.7 mm Phillips #2 screws.
Remove two 11.5 mm Phillips #2 screws.
Remove the cold water reserve arm's plug from the arm itself in order to allow access to the base screws.