Saltar al contenido principal

Huawei Honor 10 Battery Disconnect

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. Huawei Honor 10 Battery Disconnect, Rear Glass: paso 1, imagen 1 de 1
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to a long edge of the phone to loosen the adhesive beneath the rear glass. Apply the iOpener for at least two minutes.

  2. Huawei Honor 10 Battery Disconnect: paso 2, imagen 1 de 3 Huawei Honor 10 Battery Disconnect: paso 2, imagen 2 de 3 Huawei Honor 10 Battery Disconnect: paso 2, imagen 3 de 3
    • If the phone's rear glass is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

    • Press a suction cup onto the back cover.

    • Lift the back cover's right edge with your suction cup, opening a slight gap between the back cover and the frame.

    • Insert the tip of an opening pick in the gap you created and slide it to the bottom right corner.

  3. Huawei Honor 10 Battery Disconnect: paso 3, imagen 1 de 2 Huawei Honor 10 Battery Disconnect: paso 3, imagen 2 de 2
    • Apply more heat if the adhesive becomes hard to cut. During the removal process, the back cover is under tension all the time and is likely to break if the adhesive isn't softened enough.

    • Insert a second opening pick at the bottom right corner of the rear glass.

    • Slide the opening pick along the bottom edge of the rear glass to cut the adhesive and leave it in the bottom left corner.

  4. Huawei Honor 10 Battery Disconnect: paso 4, imagen 1 de 3 Huawei Honor 10 Battery Disconnect: paso 4, imagen 2 de 3 Huawei Honor 10 Battery Disconnect: paso 4, imagen 3 de 3
    • Insert a third opening pick at the bottom left corner of the rear glass.

    • Slide the opening pick along the left edge of the rear glass to cut the adhesive.

    • Leave the opening pick at the top left corner of the rear glass.

  5. Huawei Honor 10 Battery Disconnect: paso 5, imagen 1 de 2 Huawei Honor 10 Battery Disconnect: paso 5, imagen 2 de 2
    • Insert a fourth opening pick at the top left corner of the rear glass.

    • Slide the opening along the top edge of the rear glass and cut the remaining adhesive with it.

  6. Huawei Honor 10 Battery Disconnect: paso 6, imagen 1 de 2 Huawei Honor 10 Battery Disconnect: paso 6, imagen 2 de 2
    • Carefully lift the rear glass of the Huawei Honor 10 and remove it.

  7. Huawei Honor 10 Battery Disconnect, Battery disconnect: paso 7, imagen 1 de 3 Huawei Honor 10 Battery Disconnect, Battery disconnect: paso 7, imagen 2 de 3 Huawei Honor 10 Battery Disconnect, Battery disconnect: paso 7, imagen 3 de 3
    • Use a pair of tweezer to carefully peel the black foil off the loudspeaker and daughterboard cover.

    • Remove the foil completely.

  8. Huawei Honor 10 Battery Disconnect: paso 8, imagen 1 de 1
    • Remove the three Phillips #00 screws (2.9 mm length) that secure the metal bracket on top of the battery, interconnect, and display flex cable.

  9. Huawei Honor 10 Battery Disconnect: paso 9, imagen 1 de 2 Huawei Honor 10 Battery Disconnect: paso 9, imagen 2 de 2
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    • Use a pair of tweezers to remove the metal shield that covers the connectors of the interconnect cable, the battery and the display flex cable.

  10. Huawei Honor 10 Battery Disconnect: paso 10, imagen 1 de 2 Huawei Honor 10 Battery Disconnect: paso 10, imagen 2 de 2
    • Use a spudger to pry up and disconnect the battery flex cable.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Dominik Schnabelrauch

Miembro Desde 11/23/16

229,384 Reputación

682 Guías creadas

Equipo

iFixit Miembro de iFixit

Staff

118 Miembros

19,452 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 7

Ultimos 30 días: 7

Todo El Tiempo: 91