Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Shut down the computer.
-
Disconnect the power and all external devices connected to the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a Metal Spudger and remove the rubber foot closet from the bottom of the laptop.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove all of the screws located on the bottom of the laptop:
-
5 Phillips 2.4 x 5.7 mm screws
-
5 Phillips 2.0 x 5.0 mm screws
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over onto its base, with the computer open and the keyboard facing upward.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the Plastic Opening Tool to separate the keyboard from the base of the laptop.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Raise the keyboard slightly to access the touch pad and keyboard cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the ribbon cables attaching the touch pad and keyboard to the system board (motherboard).
-
Using the Heavy-Duty Spudger lift up the plastic locks connecting the ribbon cable to the motherboard.
-
Use the blue plastic tab on the ribbon cable to pull it out from the lock on the motherboard.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the Phillips 00 Screwdriver, remove 6 Phillips 2.0 x 4.6 mm screws from the perimeter of the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
(You don't NEED to remove this shielding as you can remove the board with it still there.)
-
Remove the adhesive strip.
-
Lift the shield away from the base of the laptop.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the ribbon cables attached to the system board (motherboard).
-
Using the Heavy-Duty Spudger lift up the plastic locks connecting the ribbon cable to the motherboard.
-
Use the plastic tab on the ribbon cable to pull it out from the lock on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the fastened cables from the system board (motherboard) by carefully pushing the cable's plastic edges using the Heavy Duty Spudger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the clipped cables from system board (motherboard).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the system board (motherboard).
-
Using the Phillips 00 Screw Driver, remove 9 Phillips 2.0 x 4.7 mm screws with "M2L4" next to them.
-
Using the Phillips 00 Screw Driver, remove the silver screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a Heavy Duty Spudger, disconnect the black and red RTC battery cable on the left side of the system board (motherboard).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Release the system board (motherboard) from the base enclosure.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the Phillips 00 Screw Driver, remove 5 Phillips 2.5 x 4.2 screws from the hinges from the laptop's base.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pull the display away from the base panel to unhinge.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a Metal Spudger to pry the display panel from the outer casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Open the display panel to expose the connecting cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel off the adhesive tape and remove the connected cable from the screen.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the circuit board out of the way to expose the wire underneath. Remove the wire from the base of the laptop.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.
5 comentarios
You can. Fold the computer all the way over and go from there. The only advantage to opening the bottom would be to disconnect the battery: a highly recommended procedure.
A little extra pulling the mother board out. But I guess better safe then sorry. All in all this was a good guide!
REMEMBER if your new touch screen does not work (no touch screen) go into the device manager and uninstall i2c hid device. restart the laptop and the driver (and touch) should work again.
I was able to install a new screen. However, the “touch” does not work. I tried the uninstall i2c hid (and also HID- compliant touch screen) trick, but no luck. My guess is its my fault during install. Before I go diving back in for a loose connection, does anyone know which connection I should focus on?