Repara tus cosas Comunidad Tienda

General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement

Introducción

Use this guide to replace the upper feed roller bearing in a General Pipe Cleaners Drain Cleaner PMEBO 2016.

Qué necesitas

  1. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement, Upper Feed Roller Bearing: paso 1, imagen 1 de 1

    • Before you begin, make sure the drain cleaner is disconnected from power.

    • Use your hand to unscrew and remove the feed pressure knob.

    Editar

  2. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 2, imagen 1 de 1

    • Use a 1/4 inch socket wrench to remove the three bolts securing the feed roller holder plate.

    Editar

  3. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 3, imagen 1 de 1

    • Remove the feed roller holder plate.

    Editar

  5. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 4, imagen 1 de 1

    • Use a 3/16 inch hex wrench to remove the top swing pin.

    Editar

  6. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 5, imagen 1 de 3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 5, imagen 2 de 3 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 5, imagen 3 de 3

    • Use pliers to lift out and remove the pressure spring plate.

    • Lift out and remove the pressure spring.

    Editar

  7. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 6, imagen 1 de 2 General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 6, imagen 2 de 2

    • Use pliers to lift the top carrier straight up and out of the feed body.

    • During reassembly, make sure that the carrier is oriented so that its threaded hole lines up with the swing pin hole in the feed body.

    • During reassembly, clean the carrier and apply new grease before inserting it into the feed body.

    Editar

  8. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 7, imagen 1 de 1

    • Use a 3/16 inch hex wrench to remove the feed roller shaft.

    • It may be necessary to insert a thin screwdriver or hex wrench into the top end of the carrier to help hold the carrier while you loosen the feed roller shaft.

    Editar

  9. General Pipe Cleaners Drain Cleaner PMEBO 2016 Upper Feed Roller Bearing Replacement: paso 8, imagen 1 de 1

    • Remove the upper feed roller assembly, including the fiber disks on either side of it.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

Adam O'Camb

Miembro Desde 04/11/15

197,118 Reputación

416 Guías creadas

Insignias: 39

+ 36 más insignias

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 6

Ultimos 30 días: 18

Todo El Tiempo: 833