Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Disassembling Canon EOS 60D Removing Back Panel

Introducción

This is a fairly straight-forward process. You may be able to get away without removing the rear rubber grip.

Qué necesitas

  1. Disassembling Canon EOS 60D Removing Back Panel, Eye piece and Battery door: paso 1, imagen 1 de 2 Disassembling Canon EOS 60D Removing Back Panel, Eye piece and Battery door: paso 1, imagen 2 de 2

    • Removing the eyepiece is easy. There are two methods, you can do it yourself, or put it in your camera bag a dozen times and at least once, it will fall off.

    • Grip the eyepiece by the sides firmly (index finger and thumb). Wiggle it upwards until it is off.

    Traducir

  2. Disassembling Canon EOS 60D Removing Back Panel: paso 2, imagen 1 de 2 Disassembling Canon EOS 60D Removing Back Panel: paso 2, imagen 2 de 2

    • Open the battery door

    • Rotate the door so the one side of the hinge pops out (see photo #2)

    • Slide other pin out (it pops out the same, but this is easier)

    Traducir

  3. Disassembling Canon EOS 60D Removing Back Panel, Rubber grips: paso 3, imagen 1 de 1

    • Use a thin piece of plastic, spudger, or fingernail (if you have them) to lift up the edge of the grip, and pull up slowly.

    • Repeat for the other two grips

    • The large one on the battery-side is the easiest to start with. This is required to remove the front & back panels

    • The small one on the back is a bit difficult to get started, but not really difficult to remove.

    • The one on the AV panel will be easier if you open up the AV port cover.

    • Remove the adhesive like you would rubber cement, just rub your finger against it, it will come off.

    • Optionally throw the balled up adhesive at people pretending its a booger :)

    Traducir

  5. Disassembling Canon EOS 60D Removing Back Panel, Left-Side Port Cover: paso 4, imagen 1 de 1

    • Remove 3 screws

    Traducir

    • Remove the small Screw under the Flip cover too

    Traducir

  7. Disassembling Canon EOS 60D Removing Back Panel: paso 6, imagen 1 de 1

    • Using a Spudger, fingernail, or other thin plastic tool to wedge the panel off of the camera

    • Start at the camera's front. Pulling on the rubber av-cover may be enough to get it to move off the body

    • Only pull about 1/4" (3-5mm). There is a tab that will need to slide out

    Traducir

  8. Disassembling Canon EOS 60D Removing Back Panel: paso 7, imagen 1 de 1

    • Slide the rear part of the cover out.

    Traducir

  9. Disassembling Canon EOS 60D Removing Back Panel: paso 8, imagen 1 de 2 Disassembling Canon EOS 60D Removing Back Panel: paso 8, imagen 2 de 2

    • At this point, the only thing holding on is the dust-cover is hooked onto the front panel

    • Slide down to remove without damaging the cover. (see photo with cover removed)

    • You can see how the cover, and side piece fit together in the second image.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 1 otro colaborador

Eric D

Miembro Desde 11/13/12

1,284 Reputación

5 Guías creadas

Insignias: 15

+ 12 más insignias

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 4

Todo El Tiempo: 5,008