Introducción
Esta es una guía para arreglar el "tearing" de la pantalla E-Paper en el Pebble 301BL.
*este procedimiento anula la garantía del dispositivo*
Qué necesitas
-
-
Esta es una guía para solucionar el problema de la pantalla E-Paper en relojes Pebble 301BL.
-
-
-
Usando un destornillador Torx T5; saca los 4 tornillos de la parte posterior.
-
-
-
-
Encontraras el conector de video (Video connector) en la parte inferior del dispositivo, a la izquierda del motor de vibración.
-
Durante el uso normal y debido a la falta de presión, el cable se suelta, creando los defectos en la pantalla.
-
En el siguiente paso, mostraremos como aplicar presión para mantenerlo conectado.
The rumble pack ( Circle silver bit on the bottom right ) is glued to the top of the backplate. Use a spudger to ply it from there as you could damage the cord connected to it if you pull it away with the backplate.
Dieser Konnektor ist NICHT der Video Konnektor! Er ist die Verbindung zu dem umlaufenden Flexkabel mit den Tastern.
Der Video Konnektor ist ein Gummistreifen am unteren Rand der Platine, der zwischen Platine und Display liegt.
Bei Darstellungsproblemen hilft es meist, diesen Gummistreifen herauszunehmen und ihn um 180° gedreht wieder einzulegen.
-
-
-
El método que me funcionó fue poniendo un trozo de papel higiénico encima del conector.
-
Para comprobar si esto ayuda, sujeta el papel con un dedo, y desplázate a través del menu usando los botones.
-
¡No te preocupes! Nada dentro del dispositivo hará que el papel prenda fuego.
-
-
-
Una vez que has comprobado que el papel aplica la presión necesaria, puedes volver a colocar los tornillos.
-
En caso de que no cierre correctamente, vuelve a abrir el dispositivo, quita un poco de papel hasta que cierre correctamente. Así podrá mantener su resistencia al agua.
-
-
-
Este es un ejemplo del resultado final.
Thanks, this was a real life saver. Worked like a charm, and the rapid delivery on the tools was great.
Amazing.
-
Para reensamblar el dispositivo, siga las instrucciones al revés.
Para reensamblar el dispositivo, siga las instrucciones al revés.
Cancelar: No complete esta guía.
40 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
9 comentarios
This guide sadly only works for the revised model. The kickstarter edition had no screws in the back and have to be pried open from the screen, making the repair next to impossible without badly damaging de case or/and the screen.
Would something like the iopener work for that? Have had just about every model bar the original ks edition so im not sure myself.
It is possible with heat and a ton of patients. Took a buddy of mine a whole afternoon to open it. Once he had the connector reseated, he actually used a of some sort to hold it in place instead so he wouldn't have to have the whole Pebble stuffed. Then he used the same putty/glue to help seal the watch shut. I'll see if he'll tell me what it was.
"To reassemble your device, follow these instructions in reverse order." .... so take it apart again and remove the tissue?
I see you are trying to be funny.
In case you were serious: no do not remove the tissue.
That connector isn't video, it's the antenna and buttons. The display is actually not physically connected to the board.
This astoundingly simple procedure revived my dear pebble; works like a charm!
I was very worried I had finally lost this thing after all these years. Nope, I cut a sticky note up and folded it up since I felt a little more neat. Works like a charm!