Repara tus cosas Comunidad Tienda

Brother IntelliFax-2840 Control Panel Replacement

Introducción

Use this guide to replace a damaged or malfunctioning control panel on your Brother IntelliFax-2840. The entire panel is replaced as a unit, including the buttons and display.

Qué necesitas

  1. Brother IntelliFax-2840 Control Panel Replacement, Automatic Document Feeder: paso 1, imagen 1 de 1

    • Remove the two 15 mm Phillips #1 screws securing the ADF at the rear of the fax machine.

    Editar

  2. Brother IntelliFax-2840 Control Panel Replacement: paso 2, imagen 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: paso 2, imagen 2 de 2

    • Gently pull the ADF up and away from the machine.

    Editar

  3. Brother IntelliFax-2840 Control Panel Replacement, Control Panel: paso 3, imagen 1 de 2 Brother IntelliFax-2840 Control Panel Replacement, Control Panel: paso 3, imagen 2 de 2

    • Gently lift up the control panel.

    Editar

  5. Brother IntelliFax-2840 Control Panel Replacement: paso 4, imagen 1 de 3 Brother IntelliFax-2840 Control Panel Replacement: paso 4, imagen 2 de 3 Brother IntelliFax-2840 Control Panel Replacement: paso 4, imagen 3 de 3

    • Use a finger or prying tool to gently pop off the right side control arm (furthest from the handset).

    • Repeat for the left side control arm.

    • You can make this task easier by taking the handset out of the cradle and setting it aside.

    Editar

  6. Brother IntelliFax-2840 Control Panel Replacement: paso 5, imagen 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: paso 5, imagen 2 de 2

    • Do not attempt to completely remove the control panel yet, as it is still connected by a cable.

    • Lifting from the front edge, gently flip up the control panel.

    Editar

  7. Brother IntelliFax-2840 Control Panel Replacement: paso 6, imagen 1 de 1

    • While supporting the control panel with one hand, remove the three 12.2 mm Phillips #1 screws securing the rear control panel cover.

    Editar

  8. Brother IntelliFax-2840 Control Panel Replacement: paso 7, imagen 1 de 1

    • While still supporting the control panel, use your fingers or a spudger to gently free the two plastic clips securing the rear control panel cover.

    • Slide the rear control panel cover down slightly to free it from the three clips along the upper edge.

    Editar

  9. Brother IntelliFax-2840 Control Panel Replacement: paso 8, imagen 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: paso 8, imagen 2 de 2

    • Separate the rear control panel cover from the control panel.

    Editar

  10. Brother IntelliFax-2840 Control Panel Replacement: paso 9, imagen 1 de 2 Brother IntelliFax-2840 Control Panel Replacement: paso 9, imagen 2 de 2

    • Gently pull the control panel cable straight out from its connector.

    • The control panel should now come free.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 1 otro colaborador

Geoff Wacker

Miembro Desde 09/30/13

90,075 Reputación

89 Guías creadas

Insignias: 44

+ 41 más insignias

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 5

Ultimos 30 días: 16

Todo El Tiempo: 4,274