Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the netbook upside down with the battery at the top, facing away from you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Unlock the battery by sliding the switch located near the left hinge to the left "unlocked" position.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the latch located on the opposite hinge from the lock while pushing the battery up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently loosen the two Phillips #0 screws in the small panel that covers the wireless card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables from the left side of the wireless card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 3.9 mm Phillips #1 screw from the bottom left of the wireless card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift up the left side of the wireless card and slide the card out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the netbook over and open the display so that the keyboard is facing you.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There are three tabs located on the top of the keyboard.
-
Start with the spudger pointing towards the display and pry up to push each tab off the keyboard.
-
As you move to the next tab, ensure the previous tab doesn't reset itself.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift top of keyboard up. If it doesn't lift easily, there may be tabs on the sides - use the tool to ease them aside and/or shift the keyboard from side to side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the ribbon by lifting the black plastic hinge and removing the clear blue cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close the display and turn the ZG5 over so that the battery compartment faces away from you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove three 5.8 mm Phillips #0 screws from the bottom of the case
-
Remove three 3.9 mm Phillips #1 screws from the battery compartment.
-
Remove two 5.8 mm Phillips #0 screws from underneath the feet near the hinges.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the netbook back over and open the display with the keyboard cavity facing you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip up the retaining flap on the trackpad ribbon cable ZIF connector.
-
Using the blue tab, pull the trackpad ribbon cable from its socket on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the five black 4.7 mm Phillips #0 screws from the metal casing.
-
Remove the single silver 4.3 mm Phillips #00 screw from the right side of the metal casing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting at the red rings along the hinge, insert a spudger or plastic opening tool into the seam between the two halves of the case.
-
Slide the spudger toward the front of the device, releasing the small clips that hold down the top case.
-
Gently lift off the top case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two antenna cables from the right side of the wireless card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 3.9 mm Phillips #1 screw from the wireless card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pull the wireless card to the right and slide it out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the display cable from the top left of the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the speaker cable from its socket on the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove three 3.9 mm Phillips #1 screws from the small I/O board.
-
Remove a single 3.9 mm Phillips #0 screw from the front of the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 4.7 mm Phillips #1 screws that connect the display to the motherboard.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the I/O board up from the right side of the case.
-
Cancelar: No complete esta guía.
24 personas más completaron esta guía.
Equipo
Cal Poly, Team 7-49, Amido Fall 2010 Miembro de Cal Poly, Team 7-49, Amido Fall 2010
CPSU-AMIDO-F10S7G49
5 Miembros
27 Guías creadas
2 comentarios
Hi Doug,
I'm about to rebuild my old acer netbook ZG5 and discovered that there is nothing under the wireless card door. Does this mean that the wireless card is embedded? I ask because I am now doubting that the netbook was ever wifi (but it must have been.) Newegg doesn't seem to have any motherboards available for the ZG5 so I'm thinking I'll get one from ebay. Thanks for the guide.
Matt
Bro, i got problem with this mobo...
The resistor is broke, its located on side of keyboard port...
I'm trying to de-solder but it wont move.
What should i do?
