Herramientas Destacadas en este Teardown

Introducción

This guide will show you how to completely teardown your camera.

Este desmontaje no es una guía de reparación. Para reparar tu Olympus Stylus 410, utiliza nuestros manuales de servicio .

Locate the 2 screws on the bottom of the slider.
  • Locate the 2 screws on the bottom of the slider.

  • Remove both screws with a #00 Phillips screwdriver.

Agregar Comentario

Gently pull on the bottom of the slider until it comes off the lower track.
  • Gently pull on the bottom of the slider until it comes off the lower track.

  • There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.

Agregar Comentario

  • Lift the slider up until it comes off the upper track.

Agregar Comentario

  • The slider should now be free from the body of the camera.

Agregar Comentario

  • Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

Agregar Comentario

  • Use the spudger to peel off the outer metal band, starting from the bottom of the camera.

  • The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

Agregar Comentario

  • The shutter button can now be removed. It is not connected to the camera and can be lifted off.

Agregar Comentario

  • Remove the memory card.

  • Locate and remove the 2 screws using a #00 Phillips screwdriver.

Agregar Comentario

  • Use a spudger around the edge of the case to loosen it.

  • Carefully wiggle the back case off. This may require a fair amount of force.

Agregar Comentario

  • Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

Agregar Comentario

  • While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.

  • Be careful not to completely pull the front case off because it will still be connected with wires.

Agregar Comentario

  • Locate the gray compartment covering the flash.

  • Position your flat head screw driver or small spudger underneath the tab that is keeping the gray cover on.

  • Gently lift the tab so the gray compartment becomes free.

Agregar Comentario

  • Use the spudger around the perimeter of the gray compartment to detach it from the front case.

  • The gray compartment can now be removed from the flash unit.

  • The flash unit can now be removed, and a new one soldered back on.

Agregar Comentario

  • Open the battery cover and lift it up and off of back camera case.

Agregar Comentario

  • Locate and unscrew the 2 screws with a #00 Phillips screwdriver.

  • Remove the black seal.

Agregar Comentario

  • Slide the metal piece off of the battery cover.

Agregar Comentario

  • This is what the battery cover and back case look like completely disassembled.

Agregar Comentario

  • Remove the metal frame from the LCD screen using a spudger.

Agregar Comentario

  • Pry off the LCD screen from the top using a spudger. The screen will not be completely free from the device because of a ribbon.

  • Do not pull the screen completely off because it will still be held on by two ribbon cables.

Agregar Comentario

  • This is what the camera will look like now that the LCD screen is removed.

Agregar Comentario

Rory Aronson

Miembro Desde 15/04/10

34 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 6-13, Maness Spring 2010 Miembro de Cal Poly, Team 6-13, Maness Spring 2010

CPSU-MANESS-S10S6G13

5 Miembros

9 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 3

Todo El Tiempo: 4,409