Herramientas Destacadas en este Teardown

Introducción

A Motorola V3i it's from the "RAZR" series.

The V3i had an improved camera resolution with 1,3Mpix and a external Memoryslot (MicroSD) for additional storage. Even if it had serveral problems with the keyboard and handling, it's one of the most sold mobilephones in the world.

Este desmontaje no es una guía de reparación. Para reparar tu Motorola V3i, utiliza nuestros manuales de servicio .

A Motorola V3i!
  • A Motorola V3i!

  • Let's see what's inside...

Agregar Comentario

Let's turn it and take out the battery.
  • Let's turn it and take out the battery.

  • Remove these two screws.

Agregar Comentario

  • Now you can easily flip the cover.

Agregar Comentario

  • You need to detach these two plastic lashes from the surounding.

  • Now you can remove this transparent plastic case.

  • Now you can take out the speaker.

  • The metal thing on the end of the picture is the antenna.

Agregar Comentario

  • So, that's the board.

  • Vibra motor.

  • Mini USB.

  • Connector for the antenna.

  • After I took these EMI shields away it looks like this...

Agregar Comentario

  • Bluetooth chip by Broadcom.

  • 32Mbit PSRAM by STMicroelectronics.

  • Baseband Processor (Main Processor) by Freescale (90nm structure).

  • RF Transmitter by RF Micro Devices.

  • Battery controller by Freescale.

  • Quad-Band Transmit Module by RF Micro Devices.

Agregar Comentario

  • Remove these 4 rubbers.

  • Then remove the four torx screws.

  • You can easily lose these rubbers. (That's why I have only 3 of them...)

Agregar Comentario

  • Filp the device and you can remove the top housing.

  • Remove the three buttons on the side of the device.

  • Remove the connector to the mainboard...

  • and to the camera.

The front cover can be very stubborn to remove as the clips may be very tight. Just persevere with your plastic opening tools. Two can be better than one here.

Grahame - Contestar

  • Remove the camera by lifting it up.

  • That's a 1,3Mpix camera!

Agregar Comentario

  • Lift up the speaker.

  • Then, that's a tricky part,remove all the buttons around the screen housing. Caution: They are really thin and they easily break!

  • After you did this tricky part you can lift the top of the phone away.

Agregar Comentario

  • Now lift up the front glass from the top of the device. It's held with adhesives.

  • After you did this it should look like this.

Agregar Comentario

  • Around the screen there are some lashes. Detach them to release the screen of the metal housing.

  • Then you can lift the metal housing up.

Agregar Comentario

  • The metal housing is very fragile!

  • an ATI Imageon chip! It's a mulitmedia co-processor, it is used for record video and mobile gaming. It support up to a 2Mpix camera.

Agregar Comentario

  • Again there's a small lash on the botton of the front screen housing.

  • After that you can remove the front screen with the PCB.

Agregar Comentario

  • The front screen.

  • Yes, my front screen has some dead pixels. (They are pink?!)

Agregar Comentario

  • Thank you for reading my Teardown:)

Agregar Comentario

Peddy

Miembro Desde 28/12/09

140 Reputación

2 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 7

Últimos 30 Días: 47

Todo El Tiempo: 20,707