Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

HTC Evo 3D Teardown

Escrito Por: David (y 3 de otros participantes)
Publicado: August 23, 2012
  • Comentarios: 1
  • Favoritos: 50
  • Vistas: 18.8k

Teardown

Herramientas Destacadas en este Teardown

Comprar estas herramientas

Introducción

This is only a simple teardown to take out all components that can be easily switched out.

Este desmontaje no es una guía de reparación. Para reparar tu HTC Evo 3D, utiliza nuestros manuales de servicio .

  1. First things first, Remove the back cover, battery and SD card.

    • First things first, Remove the back cover, battery and SD card.

    Traducir

  2. Remove the four T5 Torx screws.

    • Remove the four T5 Torx screws.

    • Then remove the two Phillips screws.

    • *Very sorry for dark image*

    Traducir

  3. Once the screws are all out from the exterior back case, Begin separating the front housing from the back by using a spudger or any similar tool.

    • Once the screws are all out from the exterior back case, Begin separating the front housing from the back by using a spudger or any similar tool.

    • Begin from the bottom were the battery bay is, It is the easiest way.

    • Be careful of ribbons behind the plastic

    Traducir

  4. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda

  5. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself.

    • Once separated begin to remove the LED board. Apply only light upward force and it will detach itself.

    Traducir

  6. Vibrator come's out easy, Just grab it by the wire and give it a little tug and it should come out. Start unlocking the clips holding the ribbons. pull the white tab up to unlock.

    • Vibrator come's out easy, Just grab it by the wire and give it a little tug and it should come out.

    • Start unlocking the clips holding the ribbons. pull the white tab up to unlock.

    • Example: bottom left is unlocked, bottom right is locked. upper left has bin finished and removed.

    • Tuck the ribbons in without bending or making tears in them.

    Traducir

  7. Behind the main board is two more ribbon's.

    • Behind the main board is two more ribbon's.

    • Flip both tab locks holding the ribbons and they will slide out vary easily, Don't force it.

    • Wifi/cellular antena port, Lift up cord head directly to remove and press straight down centered to put back on.

    • As a side note, the grey tape on the back side of the board was covering the clips so i cut a small section for this guide.

    Traducir

  8. This concludes the (simple) teardown of the Evo 3D.

    • This concludes the (simple) teardown of the Evo 3D.

    Traducir

Autor

con 3 otros colaboradores

David

Miembro Desde 18/03/12

9,167 Reputación

2 Guías creadas

Insignias: 33

+ 30 más insignias

Equipo

Master Techs Miembro de Master Techs

Community

285 Miembros

800 Guías creadas

Un Comentario

Agregar un comentario

Thanks. This was very helpful.

dano706 - Contestar

Agregar Comentario

1024

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 4

Últimos 30 Días: 16

Todo El Tiempo: 18,871