Harley Middleton

I have a samsung gear 360 (2017) I also have in the camera Samsung 128GB 100MB/s (U3) MicroSD EVO Select Memory Card. How...

When charging with the cable out of the box works but over the day of use does not hold a charge for very long and drops...

The number one reason most Instax cameras stop working is that the batteries need replacing. According to the manual, you can take an average of 100 shots with two new AA batteries (or around 10 rolls of film) so it is worth keeping track of just how many you’ve used up so that you can avoid any nasty surprises. Fujifilm also advises buying batteries of the same brand/type and only using alkaline batteries. If the batteries are dead or dying, one of two things can happen: all the lights on the adjustment dial will blink simultaneously or the red lamp will light up beside the viewfinder. When all the lights blink, you must replace the batteries with brand new ones while the lens is extended (on other words, with the camera turned on). Note that if you replace the batteries while the lens is retracted, the lights will continue to blink. If only the red lamp comes on, simply turn the camera off by pushing the lens back into the body and replace the batteries. Provided that the camera isn’t damaged, this...

Now with the above in mind, AT&T just shut off nearly all 2G service on their towers and T-Mobile has already started and will finish around 2020 I believe. However at any moment they can decide to make that sooner. If your area has 2G shut down, then a symptom of any phone connected to 2G will look like it "has no service." 

I have search all over and found that xda website said that this phone does’’t have this option not built into the hardware/software to customize for that setting.

Choose System Preferences from the Apple menu (), then click Startup Disk. Click the icon of the disk you normally use to start up your computer. It's usually named Macintosh HD. Close the System Preferences window. Your Mac should now start up without the flashing question mark. If your Mac starts up with a flashing question mark, but then doesn't continue starting up, try these steps. Turn off your Mac by pressing and holding the power button for a few seconds. Press the power button once to turn your Mac back on. Immediately press and hold the Command and R keys on your keyboard to start your Mac from macOS Recovery. Keep these two keys held down until you see an Apple logo or globe. If prompted, select a Wi-Fi network to connect to the Internet as part of a startup. After the macOS utility window appears, choose Startup Disk from the Apple menu. Select your startup disk, then click Restart. If you don't see your startup disk in the Startup Disk window, close the window and try the next sections of...

STEP 1: ISOLATE THE PROBLEM IMMEDIATELY As I said earlier, the error message “Unfortunately, com.sec.imsservice has stopped” can be caused by either a pre-installed app or downloaded one. So, to isolate the problem, you need to boot your Samsung Galaxy S5 in safe mode to temporarily disable all third-party apps. Turn the device off. Press and hold the Power key. When ‘Samsung Galaxy S5’ appears on the screen, release the Power key. Immediately after releasing the Power key, press and hold the Volume down key. Continue to hold the Volume down key until the device finishes restarting. Safe mode will display in the bottom left corner of the screen. Release the Volume down key when you see Safe Mode. STEP 2: DISABLE / UNINSTALL THIRD-PARTY MESSENGERS If the error message doesn’t pop up while the phone is in safe mode, it means that one of your downloaded apps caused the problem. More often instant messaging apps are the primary cause of this problem, so find them and disable or uninstall them before you boot...

Download version 9 or 10 of the Intel Management Engine Interface (MEI) Driver. Navigate HP's Software and Driver Downloads site (http://www8.hp.com/us/en/drivers.html) to find the latest approved driver for your model. Filter by version, selecting Microsoft Windows 8.1 on the dropdown menu. Look for the download in the "Driver-Chipset" category. If an MEI driver with a version number starting in 9 or 10 is listed, download it. [Version 9.5.24.1790 1.5M (http://ftp.hp.com/pub/softpaq/sp66001-66500/sp66228.exe) will work for most models.] If an MEI driver with a version number starting in 9 or 10 is NOT listed, download the appropriate driver directly from Intel (https://downloadcenter.intel.com/search?...). [Version 9.5.24.1790 1.5M (https://downloadcenter.intel.com/downloa...-ME-9-Management-Engine-Driver-for-Intel-NUC) will work for most models.] Download the Windows 10 "Show or Hide Updates" Troubleshooter Package...

Go into the Settings of your device Tap on Apps or Applications Manager (the name varies depending on your device). Swipe to the All column. Scroll down until you see Google Services Framework Finally, choose Clear data and then OK.

This will work even if the phone will not power up try this and I do this every six months just to reset this setting. Solution: Turn the phone off. Remove the battery. Wait 10 seconds. Plug in the charger. Insert the battery. Turn on the phone.

- Rebuild the database. Fully turn-off the PS4 and unplug the cord. Put the cord back in and hold down the power button until you hear a second beep. This will put it into SAFE mode. Select option 5 to rebuild the database. This method scans the PlayStation 4 drive and creates a new database of all content. It works in the same way that you defrag your PC. Do not turn the PS4 off while you’re rebuilding the database. This could take some time. - If nothing has worked, you should send your PS4 in for a service. You should check out the PlayStation Support page to find the relevant number in your country.