Repara tus cosas Comunidad Tienda

Adaptador de corriente alterna magnético de segunda generación para productos MacBook, lanzado por primera vez en 2012. No es compatible con sistemas de generaciones anteriores Disponible en versiones de 45W, 60W y 85W.

Preguntas 26 Ver todo

Opciones

Why my magsafe 2 light suddenly goes off

Been a while ago, my all electrical devices burnt because power surge that I lived, fortunately I repaired all devices except magsafe 2 45 watt, I replaced all broken power components of magsafe 2 (capacitor, varistor, fuse and inductor) then I connected 39k ohm resistor to output pins (0.6v without connecting 39k ohm) and I saw 15v on output, It worked technically and charged my MacBook as well but sometimes light turns off suddenly and charging stops, after unplugging cable and plugging it again, It starts charging again but not for long, I can't estimate what's wrong with it, thanks in advance.

Contestado! Ver respuesta Yo también tengo este problema

Es esta una buena pregunta?

Sí No
Puntuación 0
Agregar un comentario

2 Respuestas

Filtrar por:
Mas Útiles Más Reciente Más antiguo
Solución Elegida

Opciones

Here’s one system I serviced a few years ago

Block Image

Clearly the DC-In Board needed replacing as it was to far gone from a knockoff charger.

Block Image

Use a cotton swab (Q-Tip) with some 75 % or better isopropyl alcohol and if needed use a fresh (soft) pink pencil eraser to polish the contact surface rolling it in your fingers as you press down.

Make sure the white insulated area is also clean as the piled up junk can mess up the ability of the contacts to make a good connection.

Use a cotton swab (Q-Tip) with a bit of kitchen cleaner to get rid of the junk

Here’s more on knockoff chargers:

Fue útil esta respuesta?

Sí No
Puntuación 1

4 comentarios:

I cleaned the port and reset SMC as well, but nothing changed. I desoldered magsafe 2 cable and connected it to my safe 14.85 volt power supply and It charged quite well, never stopped untill %100. But when I connect cable to magsafe2 again, It sometimes turns off untill plugging it again.

- de

Looks like you need both a new MagSafe charger as well as the DC-In Board or I/O Board depending on which system you have. Which is ???

- de

I have Intel based MacBook air 13" 2017. Looks like you're right mister Dan, need a magsafe 2. I have to look used one as a student, but I keep trying to repair broken one to share

- de

@cemkozan - Here's the needed part: MacBook Air 13" (Mid 2013-2017) I/O Board and the guide to put it in Reemplazo de tarjeta entrada/salida de MacBook Air 13" Early 2017

And here's the needed MagSafe charger from Apple: Apple 45W MagSafe 2 Power Adapter for MacBook Air

Don't go cheap with a knock off or use what is claimed to be real units from Amazon or eBay as they aren't! They are you're more likely to damage your system.

- de

Agregar un comentario
Respuesta Más Útil

Opciones

Try resetting the SMC on the computer. Sometimes the SMC can affect the MagSafe charger.

Hold the shift, control, option, and power buttons for 10 seconds then see if that fixed your problem. If it didn’t, I would get a new MagSafe adapter.

Fue útil esta respuesta?

Sí No
Puntuación 1
Agregar un comentario

Añadir tu respuesta

Cem Kozan estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 7

Ultimos 30 días: 49

Todo El Tiempo: 909