Repara tus cosas Comunidad Tienda

A2116 / 2019 / Procesador quad-core i3 a 3.6 GHz, 6-core i5 a 3.0 GHz, o 6-core i7 a 3.2 GHz. Lanzada el 19 de marzo de 2019.

Preguntas 78 Ver todo

Opciones

iMac display did not stay on

I upgraded the RAM using tools and adhesive strips from this site. A few days later, the display separated from the chassis and torn some wires away from the display connector in the process.

I have a few questions:

  • What did I likely do wrong when I replaced the display? The strips are still attached to the chassis. Was I supposed to heat or significantly pressurize the display?
  • Can the ribbon cable be repaired or replaced in the display?
  • Where can I order a new display if that’s what I need?

Thanks!

John

Contesta esta pregunta Yo también tengo este problema

Es esta una buena pregunta?

Sí No
Puntuación 0
Agregar un comentario

1 Respuesta

Filtrar por:
Mas Útiles Más Reciente Más antiguo
Respuesta Más Útil

Opciones

Ouch not good ;-{

Did you follow this guide putting on the tapes? iMac Intel 21.5" Retina 4K Display 2019 Adhesive Strips Replacement do read the warnings and the notes carefully.

At this point you’ll need a new display assembly, hopefully you hadn’t damaged the logic board connector. If you think you have take some pics and post them here for us to see Agregar imágenes a una pregunta existente

Here’s the needed part: 21.5” iMac Retina 4K Display Assembly and here’s the guide Reemplazo de pantalla en la iMac Intel 2 iMac Intel 21.5" Retina 4K 2019

Imagen de iFixit

Guía

Agregar imágenes a una pregunta existente

Dificultad:

Muy fácil

—

2 - 5 minutes
Imagen de iMac Intel 21.5" Retina 4K Display 2019 Pantalla

Guía

Reemplazo de pantalla en la iMac Intel 2 iMac Intel 21.5" Retina 4K 2019

Dificultad:

Moderado

—

20 - 40 minutes
Imagen de iMac Intel 21.5" Retina 4K Display 2019 Adhesive Strips

Guía

iMac Intel 21.5" Retina 4K Display 2019 Adhesive Strips Replacement

Dificultad:

Moderado

—

10 - 30 minutes

Fue útil esta respuesta?

Sí No
Puntuación 1

1 comentario:

Thanks. TL;DR: the machine runs, I failed to cut a mic notch and I think I just need replacement data and power cables for the display along with new adhesive strips. I followed the guide mostly correctly and I have *no idea at all* why the adhesive failed. Do I need to heat it?

This is very helpful. I learned two things here:

1) I used the right guide but failed to cut a mic notch!

2) The replacement display assembly is ridiculously expensive. It's more than 70% the cost of a new machine :-(

I will post photos once I can open it up again. Right now, the machine is functioning and I'm using blue tape to hold the screen on.

The data and power tables running from the display are slightly damaged as the wires enter the connector. Can this be repaired? I will show pictures when I have them. As I said, the machine is running, but the cable(s) look damaged, so I think they will eventually be a problem. The sockets on the board look fine.

- de

Agregar un comentario

Añadir tu respuesta

JRC estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 1

Todo El Tiempo: 60