An e-cigarette vaporizer is reusable alternative to traditional smoking.

Preguntas 49 Ver todo

SMOK X Priv firmware

Hi, my x-priv bricked and I didn't find a correct firmware on the official site... The support can't help me. Anyone know the solution? Thanks

Contesta esta pregunta Yo también tengo este problema

Es esta una buena pregunta?

Calificación 1

Comentarios:

what did you use to update it? I ask because I can NOT find anything for the x-priv myself

por

when a firmware comes out somebody could leave the link, because I have a problem it says ohm too low even without any atomizer, and if they know how to solve that problem without the much better firmware, thank you!

por

Agregar un comentario

9 Respuestas

Respuesta Más Útil

I do not believe that SMOK has released a firmware update for the X-Priv. I have been looking all over their website for it but i cannot seem to find it. I believe it is because it is a newer product.

Fue útil esta respuesta?

Calificación 2
Agregar un comentario

If you bricked it, nothing will reverse it. Some mods have a reset button to stop this happening. Sorry.

Fue útil esta respuesta?

Calificación 0

Comentarios:

Remember: "bricking" a device requires over flashing, or using wrong firmware during an upgrade. To be quite honest it's usually just a stupid issue or a DoA/Failing product.

por

Agregar un comentario

If it seems dead and won't switch on, it can help to connect it to a PC with a USB cable and then try to switch it on. Worked for me when my x-priv would not start in any other way.

Fue útil esta respuesta?

Calificación 0

Comentarios:

Follow my method and it'll ALWAYS work! You figured it out.

por

Agregar un comentario

I don’t think Smok has release anything due to the X-Priv being so new. I also have a X-Priv i can’t find anything on it myself

Fue útil esta respuesta?

Calificación 0

Comentarios:

EPriv and XPriv firmwares are available on 9/1/18 from what I hear. Mag and Gpriv just dropped.

por

when a firmware comes out somebody could leave the link, because I have a problem it says ohm too low even without any atomizer, and if they know how to solve that problem without the much better firmware, thank you!

por

Agregar un comentario

Hold all buttons WITHOUT batteries and plug into a USB port. Keep holding for ten seconds, throw batteries in while still connected, disonnect and reconnect to turn on. DO NOT TRY AND TURN ON NORMALLY. Use the cable....

This will work on any __-Priv series mod.

Fue útil esta respuesta?

Calificación 0

Comentarios:

would you know how to fix a black screen on an x-priv it turned off and only occasionally turns back on it makes it very hard to use

por

the computer has variable voltage and wattage which is horrible for the batteries and the onboard capacitors even on high-end computers like my Rog Asus R50 the wattage and voltage is all over the place at all times. always use a external charger whatever charger is best for the batteries inside. a simple search and once you find out what the max amperage should be (usually 2. 1) spend 10 or $15 at Walmart for a good quality charger that actually does the trick never use a computer for charging anything it's the stupidest idea ever it's not meant for it.

Buy a nitecore dual bay charger. ($7-10 w/free shipping on eBay/Amazon) charge batteries, leave the mod as I explained in the post. Reset the batteries using both buttons to "jump" them.

how many weight device cannot be bricked unless you flashed a different from where the definition of bricks is when there is a low-level issue in this case it sounds to me like you either have a higher level issue or it's something stupid like batteries or a charge port.

por

I really need help with the SMOK X-Priv. I just received the Mod in the mail Sept 8, but it will not turn on. I've tried the above mentioned troubleshoot, but the computer won't even recognize that the Mod is plugged into the USB port. What do I do? The screen has not and will not turn on! Is this Mod defective? Do you have any suggestions?

por

Agregar un comentario

Mine completely died, wouldnt turn on for anything, I plugged it into my computer for 10 minutes. It turned back on like nothing ever happened, and been working better than it was in the first place.

Fue útil esta respuesta?

Calificación 0

Comentarios:

This is basically the exact same thing as what I said above it uses low voltage to basically reset the actual onboard computer and then uses the boot voltage to clear the nvram believe it or not most times you see a black screen that doesn't mean it's not on it just means that the full high-level functions are not available I've literally seen to completely dead mods in my life and I fix them on a daily basis.

Glad it's working!

por

Agregar un comentario

I was charging my xpriv on my computer and just left it and then woke up and just black,I bought it like a week ago too

Fue útil esta respuesta?

Calificación 0

Comentarios:

Never use a computer to charge any mod this is because it's a capacity system and obviously the computer has variable voltage and wattage which is horrible for the batteries and the onboard capacitors even on high-end computer like my RoG Asus R50 wattage and voltage is all over the place at all times. Use whatever charger is best for the batteries inside based on MaH/AMP (usually 2. 1) if using the port, spend 10 or $15 at Walmart for a good quality charger that actually does the trick never use a computer for charging anything it's a bad idea for ANY device.

Buy a Nitecore dual bay charger. ($7-10 w/free shipping on eBay/Amazon) charge batteries, RESET the mod as I explained in the post. Reset the batteries as well using both buttons to "jump" it.

A mod cannot be bricked unless you flashed a different firmware the definition of "bricked" is when there is a low-level issue in this case it sounds to me like you either have a higher level issue or it's something stupid like batteries or a charge port.

por

Agregar un comentario

Smok X Priv I took a hit off mine about a minute or two later I tried to take another hit and nothing. It seems to be working fine in every respect, but when I pushed the button to get a hit nothing happens even the time counter won’t move. I’ve never tried to load more firmware or anything else it just won’t work!

Anyone have any suggestions?

George

Fue útil esta respuesta?

Calificación 0

Comentarios:

Having this very same issue. Everything seems to work but the unit wont fire, counter bounces from 0 to.5 rapidly..

por

I am having the same issue, but only when the batteries reach half life. Anyone have suggestions?

por

Agregar un comentario

so john are you saying plug it in to your pc or not because you have to different responses one says yes it will fix it and another says no dont it will break it

Fue útil esta respuesta?

Calificación 0
Agregar un comentario

Añadir tu respuesta

Jonas Jozsef estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 Horas: 120

Últimos 7 Días: 699

Últimos 30 Días: 2,814

Todo El Tiempo: 9,493