Movies, music, multimedia in your home. Use our guides to repair home entertainment devices from surround sound A/V receivers or conventional stereo receivers to power amplifiers, preamplifier, speakers, and iPod/Bluetooth speaker systems.

Preguntas 2260 Ver todo

How to fix sound issue in Pioneer Stereo receiver?

when i turn the volume knob sometimes the sound keeps going on and off. Please help.

Contesta esta pregunta Yo también tengo este problema

Es esta una buena pregunta?

Calificación 7

Comentarios:

When everything is connected properly on my pioneer elite receiver their is no sound from the speakers. But the display of channels is on.

por

Have a poineer vsx-2014i amp the volume control does not work and we have no remote any ideas on how to fix this

por

UE22 flashing with no sound, what does this mean ?

por

Have a vs doors pioneer receiver all displays work no sound

por

Have vsx d901s pioneer receiver displays do like normal but no siound

por

Agregar un comentario

7 Respuestas

Respuesta Más Útil

a few more informations would make it easier to answer this.

but in general - most "older" (or better) stereo recievers had a potentiometer to regulate the volume - if that part is faulty (scuffed contacts) the volume knob can not longer work properly

but to see if it's defective you have to open it - maybe exchanging the part would be easier then cleaning/repairing it (if that would be possible for the used potentiometer in this device)

Fue útil esta respuesta?

Calificación 3
Agregar un comentario

STOP''italic text'' Before you pull out the soldering iron try this. Go to your local electronics parts store and get a can of Electronic control cleaner. It used to be known as "Tuner Cleaner." #

1.Unplug the amp

2.Open the case and locate the control in question, the master volume control will usually have two sections that is two pots siamesed together.

3.Find an opening in the case of each section, very few are totally sealed, and with the extension tube on the spray can squirt some cleaner in each section while rotating the volume control knob.

4.While your inside there give the rest of the controls and switches a shot. It won't hurt them and they probably need it anyway.

This will cure 99% of volume control problems. It is also a lot less dangerous and cheaper than replacing the control!

Fue útil esta respuesta?

Calificación 2
Agregar un comentario

I have an older amplifier (which is what your volume knob controls) that has the same problem. It's as Markus says. There are dead spots on the potentiometer from corrosion. I have repaired them, myself, but it will be easier to replace. You decide.

You will have to open the receiver, access the pot, desolder and remove it, then open the pot. This is the hard part, since it was never intended to be repaired. Be careful how you open it, or it will never look the same. There is a wiper arm that is moved across a series of ridges, which is just resistive wire wound around a core. The way to remove the corrosion is to burnish both the wiper and the resistor face with emery cloth. Reassmble and reinstall.

Now, since you've destroyed the pot, search the internet (eBay, etc) using the part number off the case of the pot (I hope you saved it).

Fue útil esta respuesta?

Calificación 1
Agregar un comentario

In my 35 years of repairing electronics, my success with "cleaners" has been much lower than 99%. I'd rate it closer to 5%, but even when there's success, the problem always returns. You can't find a genuine cleaner, either, since trichlorotrifluoroethane has been outlawed for consumers. Cleaning a pot is like sprinkling salt on a bird's tail: if you've gone to the trouble to get that close, just reach out and catch the bird. Moral, try the cleaner (whatever that is), but while you're in there, replace the pot.

Fue útil esta respuesta?

Calificación 0

Comentarios:

Using the same position for the volume control, year in and out wears a "hole" in the carbon track and it becomes o/c , no signal gets through at this volume level. New 250k log pot required..

por

Agregar un comentario

my pioneer ..VSX D307 receiver ,...when I turn up the volume,...it powers off,...it just started doing this after months of working fine

Fue útil esta respuesta?

Calificación 0

Comentarios:

my Yamaha did the same thing check all the connections in the back one of your wires is probably lose and it is telling it to shut off for safety reasons.

por

Agregar un comentario

I get no sound at all

Fue útil esta respuesta?

Calificación 0
Agregar un comentario

I have a pioneersx203 home system it cut off i had it crunk up

Fue útil esta respuesta?

Calificación 0

Comentarios:

i just installed a pioneer MVH-1400NEX into i my mazda 3. when i have the volume up all the way on the stereo it hardly sounds like it’s even playing. the sound is so quiet. help!?

por

Agregar un comentario

Añadir tu respuesta

lancslad55 estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 Horas: 23

Últimos 7 Días: 141

Últimos 30 Días: 692

Todo El Tiempo: 22,714