Saltar al contenido principal

Guías de reparación y soporte para los aspiradores robóticos autónomos Roomba fabricados por iRobot.

Preguntas 163 Ver todo

Vacuum will not go straight

I am having the "circle of death" problem with my Roomba Scheduler vacuum. Vacuum just turns around in a circle. Any solutions for this?

Contestado! View the answer Yo también tengo este problema

Es esta una buena pregunta?

Calificación 4

Comentarios:

Please add more information so that we can help you out. Have you tried cleaning the wheels? Hair can often get stuck in there, causing unnecessary friction.

por

Becky Duncan, which Roomba do you have?

por

630 iRobot roomba

por

this topic will be helpful for everyone, thanks alot for this.

por

Mostrar 1 comentario más

Agregar un comentario

7 Respuestas

Solución Elegida

Becky Duncan, on a Roomba, this is called the"Circle Dance" not the "Circle of Death" :-) Here are a couple of things you can try before you get a chance to tell us which specific model you have. DRIVE WHEEL Module inspection and cleaning

Check the wheels for obstructions.

Push the wheels up and down several times and shake out any loose debris that may be trapped in the wheel well.

Make sure the wheels turn freely.

If there is uneven resistance between the wheels, hold down Roomba’s SPOT and

DOCK buttons for 10 seconds to reset the robot and try again.

Check tires for wear and tear.

If tire treads are no longer visible, or if large tears are present, replace wheel modules.

If wheel module problems persist on flat surfaces when there are no obstacles present, replace wheel modules.

The other thing to consider is dirt/grime at the optical encoders that sense wheel motion. Take a look at those and clean those with some isopropyl alcohol. Last but not least, you can also check the drive motor on the module.

There are two wires, a Red and a Black one that connect to the motor.Find those two wires on the connector that plugs into the connector on the main board, apply power form a 9V battery to those wires, the motor should turn in one direction. than reverse the wires, and the motor should turn into the opposite direction. If it does not, replace the motor, if it does you may have a bad component, either a diode or a power transistor (pretty common) on the H Bridge. Hope this helps, good luck.

Block Image

Fue útil esta respuesta?

Calificación 5
Agregar un comentario

In my Roomba 620 one of the wheels stopped turning because it came off it's shaft.

You can diagnose by turning the wheel by hand - it should turn loosely without much resistance, compared to the other wheel.

I fixed this by cleaning the shaft and the socket and then attaching the wheel back. I had to press very hard to get the wheel far enough on the shaft.

It's really weird that the wheel came off like that considering how tightly it fits. Maybe it was poorly attached initially.

Fue útil esta respuesta?

Calificación 1

Comentarios:

mine is going only backward?

por

Agregar un comentario

Just a few ideas. (1) The wheel to the outside of the circle has a broken speed sensor. Could be a cracked magnet disk that is on the back of the motor. Do a visual inspection on the magnetic disk. You can see it on the back end of the motor.The fix is a new Left wheel assembly. If you run the built in test (instructions all over the place, you tube and more) You can see the left wheel turn very fast, like maximum speed, The right wheel will be slower. The fix is a new Left wheel assembly. (2) Mother board is not reading one or the other wheel sensor. This is a last resort thing. Easy to trouble shoot with an oscilloscope. (3) Right wheel fouled with crud causing it to run slow. Clean it with another real vacuum or blow out with compressed air. (4) Front Sensor covered with junk. Blow compressed air between the front bumpers and the panel inside.

Fue útil esta respuesta?

Calificación 0
Agregar un comentario

The broken /stuck motor will be the one on the inside of the circle. If one of the wheels is turning and the other is stopped, the stopped one acts like an anchor and the other wheel drives in a circle around it. If a wheel is slower than the other, it will be the one closer to the center of the circle.

Fue útil esta respuesta?

Calificación 0

Comentarios:

Mine will turn to the right then turn to the leftwhen you touch either of the swithches on the bumper pad but not go straight

por

I cleaned all the wheels and checked for lint in the switches and wheels

por

still doesn`t work

por

Agregar un comentario

mine one is going backward?

Fue útil esta respuesta?

Calificación 0
Agregar un comentario

Is the Roomba running on dark carpets? Sometimes this will cause it to only go backwards. The Cliff Sensors react to the dark surface as though it was a cliff. It’s kind of odd but it’s possible. Another thing you might try is to check the cliff sensors for dust or dirt. They should be located at the front of the Roomba.

Fue útil esta respuesta?

Calificación 0

Comentarios:

No. I have light-colored carpets.

por

I would still suggest checking the Cliff Sensors for dust or maybe a loose connection. That might require taking off the front of the Roomba though.

por

Oh you might check the front center wheel too. If you have pets, their pet hair can get trapped in the sides of the wheel and the roomba will sense something wrong. I think the problem is most likely the cliff sensors though.

por

Any luck Steve?

por

Agregar un comentario

I have replaced: battery, wheels, and new bumper sensor harness. Now keeps telling me to “Move rumba to a new location and push start” over and over again.

Fue útil esta respuesta?

Calificación 0

Comentarios:

You've done a lot of good work it sounds like! What it's asking you to do is to place the roomba in the middle of a room with no objects around it (including carpet) and then start it. Let me know if this helps.

por

Agregar un comentario

Añadir tu respuesta

Becky Duncan estará eternamente agradecido.
Ver Estadísticas:

Ultimas 24 Horas: 23

Últimos 7 Días: 178

Últimos 30 Días: 959

Todo El Tiempo: 18,362