Saltar al contenido principal
Ayuda

Versión actual por: Nick ,

Texto:

It is possible to repair the problem, but with how dense a MicroUSB port is it won't be easy. What you need to do is take the phone apart and remove the motherboard to get to the port. You can see howw [https://www.ifixit.com/Guide/Samsung+Captivate+Motherboard+Replacement/6823|here].
Once the phone is apart you'll need a good soldering iron or rework station. You aren't going to able to use the cheapest iron you can get for this repair.
If you use a soldering iron what you want to do is put some flux on the connector and put the braid on the pins. Once you think you have it off just enough lift the wick up '''while keeping the soldering iron on it.''' See if you got rid of all the solder. If not, rinse and repeat
Once you do that, go to the ground clips and desolder those the same way. Once you remove all four lift the old connector off.
It is possible to repair the problem, but with how dense a MicroUSB port is it won't be easy. What you need to do is take the phone apart and remove the motherboard to get to the port. You can see howw [https://www.ifixit.com/Guide/Samsung+Captivate+Motherboard+Replacement/6823|here].
Once the phone is apart you'll need a good soldering iron or rework station. You aren't going to able to use the cheapest iron you can get for this repair.
If you use a soldering iron what you want to do is put some flux on the connector and put the braid on the pins. Once you think you have it off just enough lift the wick up '''while keeping the soldering iron on it.''' See if you got rid of all the solder. If not, rinse and repeat
Once you do that, go to the ground clips and desolder those the same way. Once you remove all four lift the old connector off.
 
you will needOnce you get it off, take your phone apartreplacement connector and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will
put it on the board. Then you want to use a desoldering braid and remove any old solder from the connector ONLYground pins in to keep it intact and replacein the jack

get
same place. After soldering the grounds in, put some solder on the tip of the iron and push down. Do not use a female micro USB connectorlot of solder. Do this for all of the pins on eBay(notethe new connector. Once this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess
done verify there are no shorts. If there are, fix them before powering up the contact pads ifphone and charging it.
If
you dodid this correctly you should have a working phone. If you have a hot air station, just mask off the board and remove it that way. It's also a lot easier too.
you will needOnce you get it off, take your phone apartreplacement connector and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will
put it on the board. Then you want to use a desoldering braid and remove any old solder from the connector ONLYground pins in to keep it intact and replacein the jack

get
same place. After soldering the grounds in, put some solder on the tip of the iron and push down. Do not use a female micro USB connectorlot of solder. Do this for all of the pins on eBay(notethe new connector. Once this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess
done verify there are no shorts. If there are, fix them before powering up the contact pads ifphone and charging it.
If
you dodid this correctly you should have a working phone. If you have a hot air station, just mask off the board and remove it that way. It's also a lot easier too.

Estatus:

open

Editado por: Nick ,

Texto:

ThisIt is possible to dorepair the problem, but toughwith how dense a MicroUSB port is it won't be easy. What you need to do is take the phone apart and remove the motherboard to get to the port.
ThisIt is possible to dorepair the problem, but toughwith how dense a MicroUSB port is it won't be easy. What you need to do is take the phone apart and remove the motherboard to get to the port.
 
you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this
 
You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack
 
get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)
 
note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

open

Editado por: oldturkey03 (detalles del voto) ,

Texto:

This is possible to do, but tough

you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack

get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

deletedopen
deletedopen

Editado por: mayer ,

Texto:

This is possible to do, but tough

you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack

get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

opendeleted
opendeleted

Editado por: oldturkey03 (detalles del voto) ,

Texto:

This is possible to do, but tough

you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack

get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

deletedopen
deletedopen

Editado por: oldturkey03 (detalles del voto) ,

Texto:

This is possible to do, but tough

you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack

get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

opendeleted
opendeleted

Aporte original por: Nick ,

Texto:

This is possible to do, but tough

you will need your phone apart and a soldering iron that has good heat transfer and gets hotter then 400 degrees(410 is fine) to do this

You will want to use a desoldering braid and remove any old solder from the connector ONLY and replace the jack

get a female micro USB connector on eBay(note this is cheap, so i trust eBay for this)

note you cannot do it too long, you will mess up the contact pads if you do

Estatus:

open