Saltar al contenido principal
Ayuda

Versión actual por: mayer ,

Título:

SCSI PCI card bus controller

Texto:

I got in a PowerMac 8100/80 today with some data the customer needs on it.  I thought no problem, I'll just drop in a USB PCI card.  Upon opening, it is NuBus.  Pulled the hard drive and put in an external SCSI enclosure.  Put a SCSI PCI card in to my MDD.  The external drive is not seen.  Checked my system profiler and see no SCSI driver.  Any idea on where to get one that will work with 10.5.8. By the way, the 8100/80 still runs just fine, but does seem a bit slow and needs a battery.  Not bad for a machine that's older than Nick!

UPDATE

Seagate ST19171N, 1 5/8", 10 pairs of jumpers, 4 pair block on first four pair, skip one and a jumper, four bare pair,  standard SCSI external box with two 50 pin centronics. No terminator block on box.  Cable is a 50 pin to 25 centronics.  PCI SCSI II Apple brand card

Dispositivo:

Power Mac G4 MDD

Estatus:

open

Respuesta Aceptada:

+51631

Editado por: originalmachead ,

Título:

SCSI PCI card bus controller

Texto:

I got in a PowerMac 8100/80 today with some data the customer needs on it.  I thought no problem, I'll just drop in a USB PCI card.  Upon opening, it is NuBus.  Pulled the hard drive and put in an external SCSI enclosure.  Put a SCSI PCI card in to my MDD.  The external drive is not seen.  Checked my system profiler and see no SCSI driver.  Any idea on where to get one that will work with 10.5.8. By the way, the 8100/80 still runs just fine, but does seem a bit slow and needs a battery.  Not bad for a machine that's older than Nick!

UPDATE

Seagate ST19171N, 1 5/8", 10 pairs of jumpers, 4 pair block on first four pair, skip one and a jumper, four bare pair,  standard SCSI external box with two 50 pin centronics. No terminator block on box.  Cable is a 50 pin to 25 centronics.  PCI SCSI II Apple brand card

Dispositivo:

Power Mac G4 MDD

Estatus:

open

Editado por: mayer ,

Título:

SCSI PCI card bus controller

Texto:

I got in a PowerMac 8100/80 today with some data the customer needs on it. I thought no problem, I'll just drop in a USB PCI card. Upon opening, it is NuBus. Pulled the hard drive and put in an external SCSI enclosure. Put a SCSI PCI card in to my MDD. The external drive is not seen. Checked my system profiler and see no SCSI driver. Any idea on where to get one that will work with 10.5.8. By the way, the 8100/80 still runs just fine, but does seem a bit slow and needs a battery. Not bad for a machine that's older than Nick!
UPDATE
-Seagate ST19171N, 1 5/8", 10 pairs of jumpers, 4 pair block on first four pair, skip one and a jumper, four bare pair, standard SCSI external box with two 50 pin centronics. Cable is a 50 pin to 25. PCI SCSI II Apple brand card
+
+Seagate ST19171N, 1 5/8", 10 pairs of jumpers, 4 pair block on first four pair, skip one and a jumper, four bare pair, standard SCSI external box with two 50 pin centronics. No terminator block on box. Cable is a 50 pin to 25 centronics. PCI SCSI II Apple brand card

Dispositivo:

Power Mac G4 MDD

Estatus:

open

Editado por: mayer ,

Título:

SCSI PCI card bus controller

Texto:

I got in a PowerMac 8100/80 today with some data the customer needs on it. I thought no problem, I'll just drop in a USB PCI card. Upon opening, it is NuBus. Pulled the hard drive and put in an external SCSI enclosure. Put a SCSI PCI card in to my MDD. The external drive is not seen. Checked my system profiler and see no SCSI driver. Any idea on where to get one that will work with 10.5.8. By the way, the 8100/80 still runs just fine, but does seem a bit slow and needs a battery. Not bad for a machine that's older than Nick!
+
+UPDATE
+Seagate ST19171N, 1 5/8", 10 pairs of jumpers, 4 pair block on first four pair, skip one and a jumper, four bare pair, standard SCSI external box with two 50 pin centronics. Cable is a 50 pin to 25. PCI SCSI II Apple brand card

Dispositivo:

Power Mac G4 MDD

Estatus:

open

Aporte original por: mayer ,

Título:

SCSI PCI card bus controller

Texto:

I got in a PowerMac 8100/80 today with some data the customer needs on it.  I thought no problem, I'll just drop in a USB PCI card.  Upon opening, it is NuBus.  Pulled the hard drive and put in an external SCSI enclosure.  Put a SCSI PCI card in to my MDD.  The external drive is not seen.  Checked my system profiler and see no SCSI driver.  Any idea on where to get one that will work with 10.5.8. By the way, the 8100/80 still runs just fine, but does seem a bit slow and needs a battery.  Not bad for a machine that's older than Nick!

Dispositivo:

Power Mac G4 MDD

Estatus:

open