Saltar al contenido principal
Ayuda

Versión actual por: oldturkey03 ,

Texto:

bert mackey, try this:"
 
A/C Compressor, replacing
 
1 . Following manufacturer's instructions, connect an approved refrigerant recovery/recycling/recharging unit to A/C system and discharge system .
 
WARNING
 
Do not discharge/charge the A/C system without proper equipment and training. Damage to the vehicle and personal injury may result.
 
2. Remove splash shield from under engine.
 
3. Mark A/C drive belt with direction of rotation . Remove A/C belt tensioner trim cap. See Fig. 34.
 
[image|364395|align=center]
 
4. On 4-cylinder engines: Loosen A/C belt tensioner bolt under trim cap, then remove belt from A/C compressor.
 
[image|364396|align=center]
 
Fig. 35 . 4-cylinder engines: Loosen retaining bolt A on tensioner to release drive-belt tension. To increase tension, rotate pulley in direction of arrow, then tighten bolt A.
 
5. On 6-cylinder engines: Release tension on A/C belt by turning tensioner pulley clockwíse (against spring tension).See Fig. 36.
 
[image|364397|align=center]
 
6. Disconnect electrical harness connector from compressor.
 
7. Remove A/C pressure hose and suction hose flange bolts from compressor. Plug hoses immediately See Fig . 37.
[image|364399|align=center]
[image|364399|align=center]
8 . Remove compressor mounting bolts . See Fig . 38. Re-move compressor by pulling downward from underneath car.
 
[image|364398|align=center]
 
9. Installation is reverse of removal.
 
CAUTION-
 
" Always replace O-rings when reconnecting refrigerant fines.
 
" When installing a new compressor always replace receiver/drier unit.
 
10. Before recharging, evacuate system for at least 30 min.Recharge system following equipment manufacturer'. Hope this helps, good luck.

Estatus:

open

Editado por: oldturkey03 ,

Texto:

bert mackey, try this:"
 
A/C Compressor, replacing
 
1 . Following manufacturer's instructions, connect an approved refrigerant recovery/recycling/recharging unit to A/C system and discharge system .
 
WARNING
 
Do not discharge/charge the A/C system without proper equipment and training. Damage to the vehicle and personal injury may result.
 
2. Remove splash shield from under engine.
 
3. Mark A/C drive belt with direction of rotation . Remove A/C belt tensioner trim cap. See Fig. 34.
 
[image|364395|align=leftimage|364395|align=center]
[image|364395|align=leftimage|364395|align=center]
 
4. On 4-cylinder engines: Loosen A/C belt tensioner bolt under trim cap, then remove belt from A/C compressor.
 
[image|364396|align=leftimage|364396|align=center]
[image|364396|align=leftimage|364396|align=center]
 
Fig. 35 . 4-cylinder engines: Loosen retaining bolt A on tensioner to release drive-belt tension. To increase tension, rotate pulley in direction of arrow, then tighten bolt A.
 
5. On 6-cylinder engines: Release tension on A/C belt by turning tensioner pulley clockwíse (against spring tension).See Fig. 36.
 
[image|364397|align=leftimage|364397|align=center]
[image|364397|align=leftimage|364397|align=center]
 
6. Disconnect electrical harness connector from compressor.
 
7. Remove A/C pressure hose and suction hose flange bolts from compressor. Plug hoses immediately See Fig . 37.
 
8 . Remove compressor mounting bolts . See Fig . 38. Re-move compressor by pulling downward from underneath car.
 
[image|364398|align=leftimage|364398|align=center]
[image|364398|align=leftimage|364398|align=center]
 
9. Installation is reverse of removal.
 
CAUTION-
 
" Always replace O-rings when reconnecting refrigerant fines.
 
" When installing a new compressor always replace receiver/drier unit.
 
10. Before recharging, evacuate system for at least 30 min.Recharge system following equipment manufacturer'. Hope this helps, good luck.

Estatus:

open

Aporte original por: oldturkey03 ,

Texto:

bert mackey, try this:"

A/C Compressor, replacing

1 . Following manufacturer's instructions, connect an approved refrigerant recovery/recycling/recharging unit to A/C system and discharge system .

WARNING

Do not discharge/charge the A/C system without proper equipment and training. Damage to the vehicle and personal injury may result.

2. Remove splash shield from under engine.

3. Mark A/C drive belt with direction of rotation . Remove A/C belt tensioner trim cap. See Fig. 34.

[image|364395|align=left]

4. On 4-cylinder engines: Loosen A/C belt tensioner bolt under trim cap, then remove belt from A/C compressor.

[image|364396|align=left]

Fig. 35 . 4-cylinder engines: Loosen retaining bolt A on tensioner to release drive-belt tension. To increase tension, rotate pulley in direction of arrow, then tighten bolt A.

5. On 6-cylinder engines: Release tension on A/C belt by turning tensioner pulley clockwíse (against spring tension).See Fig. 36.

[image|364397|align=left]

6. Disconnect electrical harness connector from compressor.

7. Remove A/C pressure hose and suction hose flange bolts from compressor. Plug hoses immediately See Fig . 37.

8 . Remove compressor mounting bolts . See Fig . 38. Re-move compressor by pulling downward from underneath car.

[image|364398|align=left]

9. Installation is reverse of removal.

CAUTION-

" Always replace O-rings when reconnecting refrigerant fines.

" When installing a new compressor always replace receiver/drier unit.

10. Before recharging, evacuate system for at least 30 min.Recharge system following equipment manufacturer'. Hope this helps, good luck.

Estatus:

open