Saltar al contenido principal
Ayuda

Versión actual por: Dan ,

Texto:

Casper Smit, that sounds like it would be a very drastic replacement. The very first thing I would do, is to check this out:"
 
LED #1
 
• Indicates that the trickle voltage from the power supply has been detected by the main logic board. This LED will remain ON whenever the iMac is connected to a working AC power source. The LED will remain on even when the computer has been shut down or put to sleep. The LED will turn off only if the AC power source is disconnected or the power supply is faulty.
 
LED #2
 
• Indicates that the main logic board has detected proper power from the power supply when the computer is turned on and that logic board voltage regulators are functioning properly. This LED will be ON when the computer is turned on and the power supply is working correctly.
 
LED #3
 
• Indicates that the computer and the video card are communicating. This LED will be ON when the computer is communicating properly with the video card. If LEDs 1 and 2 are ON and you heard the startup sound, but LED 3 is OFF, then the video card might be installed incorrectly or need replacement.
 
LED #4
 
• Indicates that the computer and the LCD panel are communicating. This LED will be ON when the computer is turned on and video signal is being generated. If the LED is ON and there is no image on the display, then the LCD panel, the LED backlight board, or the cables between might be installed incorrectly or need replacement.
 
LED Startup Sequence
 
LED #1 = Power available.
 
If no LED is visible:
 
• Verify AC source
 
• Verify known-good AC cable is connected
 
• Verify cable connection between AC inlet and power supply
 
• Verify cable connection between power supply and logic board
 
• Verify power supply
 
'''LED #1 + LED #2 = Power available, and system is powered on.
 
If second LED is not visible when power button is pressed:
 
• Verify power button connection to logic board
 
• Verify power button functionality
 
• Verify cable connection between power supply and logic board
 
• Verify power supply
 
• Verify logic board'''board
• Verify logic board'''board
 
andAnd as you see, the logic board is on the bottom of the list of itemstoitems to replace. I would start by checking all connectors and cables, and if you need to replace anything start with the power supply. Do check the capacitors on the PSU, make sure that they are not bulging or leaking. That would be an easy fix. My

My
usual disclaimer of course is that I am not a Mac person and I am sure that the Mac gurus can help you more than I can. Good luck.luck!
andAnd as you see, the logic board is on the bottom of the list of itemstoitems to replace. I would start by checking all connectors and cables, and if you need to replace anything start with the power supply. Do check the capacitors on the PSU, make sure that they are not bulging or leaking. That would be an easy fix. My

My
usual disclaimer of course is that I am not a Mac person and I am sure that the Mac gurus can help you more than I can. Good luck.luck!

Estatus:

open

Aporte original por: oldturkey03 ,

Texto:

Casper Smit, that sounds like it would be a very drastic replacement. The very first thing I would do, is to check this out:"

LED #1

• Indicates that the trickle voltage from the power supply has been detected by the main logic board. This LED will remain ON whenever the iMac is connected to a working AC power source. The LED will remain on even when the computer has been shut down or put to sleep. The LED will turn off only if the AC power source is disconnected or the power supply is faulty.

LED #2

• Indicates that the main logic board has detected proper power from the power supply when the computer is turned on and that logic board voltage regulators are functioning properly. This LED will be ON when the computer is turned on and the power supply is working correctly.

LED #3

• Indicates that the computer and the video card are communicating. This LED will be ON when the computer is communicating properly with the video card. If LEDs 1 and 2 are ON and you heard the startup sound, but LED 3 is OFF, then the video card might be installed incorrectly or need replacement.

LED #4

• Indicates that the computer and the LCD panel are communicating. This LED will be ON when the computer is turned on and video signal is being generated. If the LED is ON and there is no image on the display, then the LCD panel, the LED backlight board, or the cables between might be installed incorrectly or need replacement.

LED Startup Sequence

LED #1 = Power available.

If no LED is visible:

• Verify AC source

• Verify known-good AC cable is connected

• Verify cable connection between AC inlet and power supply

• Verify cable connection between power supply and logic board

• Verify power supply

'''LED #1 + LED #2 = Power available, and system is powered on.

If second LED is not visible when power button is pressed:

• Verify power button connection to logic board

• Verify power button functionality

• Verify cable connection between power supply and logic board

• Verify power supply

• Verify logic board'''

and as you see, the logic board is on the bottom of the list of itemsto replace. I would start by checking all connectors and cables, and if you need to replace anything start with the power supply. Do check the capacitors on the PSU, make sure that they are not bulging or leaking. That would be an easy fix. My usual disclaimer of course is that I am not a Mac person and I am sure that the Mac gurus can help you more than I can. Good luck.

Estatus:

open