iFixit - Answers With Device "KitchenAid Mixer"

KitchenAid Artisan Mini Mixer: Como reparar los engranes?

Fri, 01 May 2026 23:08:22 -0700

Los engranes de la batidora no sirven y por ese motivo la batidora no gira

⟐ Answered mayo 01, 2026 at 23:08 GMT-7

KitchenAid Professional 600: como cambiar la escobilla de la batidora

Mon, 28 Apr 2025 11:29:22 -0700

no se como cambiar la escobilla de la batidora kitchenaid professional 600

⟐ Commented abril 28, 2025 at 11:29 GMT-7

KitchenAid Artisan Mini Mixer: Por que se tranca la batidora

Wed, 19 Feb 2025 06:19:09 -0700

La batidora cuando pasa a velocidad uno se tranca y empieza hacer fuerza y no deja avanzar

KitchenAid KHM512ER: Porque no giran las patas de la batidora

Wed, 15 Jan 2025 06:56:06 -0700

La máquina prende pero no dan vuelta las patitas

⟐ Answered enero 15, 2025 at 6:56 GMT-7

KitchenAid Mixer: Cabezal Kitchenaid Heavy Duty no está bien fijo

Mon, 18 Nov 2024 18:48:04 -0700

Se ha debido de aflojar algo ya que el cabezal se mueve mucho si la pongo en marcha. Cómo puedo volver a ajustar correctamente el cabezal al soporte vertical y base del aparato 5KSM7591XBWH?

⟐ Answered noviembre 18, 2024 at 18:48 GMT-7

KitchenAid Artisan Mini Mixer: Porque pierde la fuerza si el motor funciona bien

Mon, 11 Mar 2024 09:21:47 -0700

Parece que los engranajes de gastaron, como los cambio?

⟐ Answered marzo 11, 2024 at 9:21 GMT-7

KitchenAid Professional 600: Como puedo remover para parte de abajo del engranaje?

Wed, 19 Jul 2023 20:15:26 -0700

La parte baja del engranaje está atascada y quiero desarmarla ya removi toda la parte de arriba donde esta el engranaje principal pero aun no logro remover la parte baja

⟐ Commented julio 19, 2023 at 20:15 GMT-7

KitchenAid Mixer: My 4KSM5PSGR proline series mixer stopped working

Tue, 28 Jul 2026 06:59:02 -0700

I have a KitchenAid Pro Line 4KSM5PSGR mixer that stopped working under load.

I opened it up and found the worm gear is worn/stripped.
Where can I get a replacement?

When I ran the motor without the gears attached, it makes a bad noise. I don't know if the carbon brushes need to be replaced.
How can I tell if the brushes need to be replaced or if it is something else?

I've attached some images of the brushes.

UPDATE: Here is a picture of the commutators

⟐ Commented julio 28, 2026 at 6:59 GMT-7

KitchenAid KSM150PSER: Interference filter board installation

Wed, 24 Jun 2026 10:25:50 -0700

Hi,

I need to fit a new interference filter board to my mixer, part number rfi pub 9705132 but can’t see how it screws to the body of the mixer. Any help would be appreciated.

⟐ Answer accepted junio 24, 2026 at 10:25 GMT-7

KitchenAid Professional 600: Stop working after being plugged to 220V instead of 110V

Wed, 10 Jun 2026 08:30:53 -0700

Our Kitchenaid have been plugged to 220V instead of 110V by mistake. After a big sound, the power transformer and the Kitchenaid stop working. I tested kitchenaid on an other power transformer but it does not turn on at all. I opened it but there is no burn smell or melted cable. Do you have any idea of what I can do to try to fix it?

⟐ Commented junio 10, 2026 at 8:30 GMT-7

KitchenAid Artisan Mixer: Makes loud grinding noise

Tue, 09 Jun 2026 01:57:32 -0700

It makes a loud grinding noise occasionally during use

KitchenAid Classic Mixer K45SSWH: My mixer makes a high pitch grinding noise

Tue, 02 Jun 2026 18:58:15 -0700

My mixer makes an intermittent high pitch grinding noise especially on high speed. How do I fix it?

KitchenAid Mixer: Mixer going too fast despite adjustment

Sat, 30 May 2026 08:00:56 -0700

Hi folks!

Got a bit of a weird one and I was wondering if anyone had seen something similar.

It's an American model mixer, KSM150 (KSM150PSOB), came to me initially with uncertain history and no speed control. (I'm in the UK, running it off of a step-down transformer, which I know isn't ideal, but I have anecdotal evidence that this works fine for many friends with US model mixers).

When it turned up, the weights were disassembled from the governor and they were loose in the case.

I reassembled the governor and replaced the phase control board (making sure it was the correct part for the US model), and after that there was a difference in the speed settings, but all the speeds still seemed too fast no matter how I adjusted the speed control plate.

I then replaced the governor AND the speed control plate. The changes in speed between settings seem more pronounced now, but stir is still more than twice as fast as it should be no matter where I set the speed adjustment screws.

I might just have to give up on it, but thought I'd ask in case anyone knows what else it could be?

Thanks in advance!

KitchenAid Professional 600: Accessory drive won't turn unless pushed in.

Mon, 18 May 2026 16:12:40 -0700

My Kitchen Aid Pro 600 recently stopped turning the planetary shaft. I disassembled it and found that the play in the shaft was allowing the bevel gear to slide above the pin that engages the shaft. I replaced the composite washer at the bottom of the planetary shaft with at thicker one, and that eliminated the vertical play in the shaft so the bevel gear again engages the pin; however, now the accessory drive shaft will only turn if held in from the outside, as though it were missing a thrust washer, but there was no washer when I first disassembled it months ago for a different repair, and none of the videos I've watched show one, either. Seem unlikely that the gears would be that worn, but I'm no expert. Any ideas?

KitchenAid Mixer: My Kitchenaid mixer won't start.

Thu, 09 Apr 2026 01:24:06 -0700

My KitchenAid Mixer is only a bit over a year old.

Last week I was using it to make bread dough. I stopped the mixer to touch the dough to see how it was coming. It wouldn't turn back on, the mixer was a little warm so I decided to finish kneading by hand and let it cool off.

I never thought of it again until I went to make brownies today and it still wouldn't start. Tried a different plugin and no dice.

What I've done:

I checked the brushes on the sides of the mixer, they look in perfect condition. Also made sure they were inserted properly.

I checked the switch itself by taking off the back cover and used a multimeter to check that when switch is on, it was making a connection.

⟐ Commented abril 09, 2026 at 1:24 GMT-7

KitchenAid Professional 600: Why does the planetary unit fall out?

Thu, 26 Mar 2026 03:14:56 -0700

The planetary unit falls out of my mixer. Nothing seems to be securing it. I can push it back in but it won’t stay.

⟐ Answered marzo 26, 2026 at 3:14 GMT-7

KitchenAid Mixer: Need help with speed control on early 1970s K45 mixer

Mon, 09 Feb 2026 01:54:14 -0700

I accidentally loosened the bottom speed control screw, and it came out. I have the screw, a nut and a bracket that the screw seems to fit into, but if I reattach it, the mixer stays in high speed.

My mixer is pre-solid state.

⟐ Answer accepted febrero 09, 2026 at 1:54 GMT-7

KitchenAid Professional 6000HD: Repair manual to reinstall gears in transmission

Tue, 27 Jan 2026 14:13:24 -0700

Gears fell out and need directions to replace back in transmission.

KitchenAid Mixer: Pro 600 makes a clicking noise after repair and regrease

Wed, 21 Jan 2026 13:02:31 -0700

The planetary hub was falling off while using the flour mill. I watched some videos and learned how to disassemble and reassemble it. Instead of replacing the hub, I used JB Weld to reattach the shaft. I cleaned everything very well, greased all the gears according to instructions, and packed the case with new Superlube food grade grease. Now it makes a clicking noise that it never did before. It's frequency matches the speed, and it sounds like it is coming from the motor end of the transmission. Any ideas about what would cause that? The only thing I have found in researching it is the possibility of too much grease in the case, but other videos have said to pack it pretty full.

⟐ Commented enero 21, 2026 at 13:02 GMT-7

KitchenAid Artisan Mini Mixer: Does not reliably power on

Sun, 18 Jan 2026 03:04:06 -0700

My mixer does not reliably power on. I see that the larger mixers have easily accessible brushes that can be replaced to fix this problem. These are not present on the mini. How can I fix this?

⟐ Answered enero 18, 2026 at 3:04 GMT-7