iFixit - Answers With Device "Amana Washing Machine"

Amana Washing Machine: lavadora amana al conectarla activa bomba de agua si la apago luego aa

Sun, 22 Mar 2026 01:36:05 -0700

lavadora al conectarla ala corriente activa la bomba de drenaje , si la apago al elegir ciclo solo prende las loces del tablero coge agua y no se detiene

⟐ Commented marzo 22, 2026 at 1:36 GMT-7

Amana Washing Machine NTW4516FW: cual es el componente

Tue, 10 Feb 2026 10:29:17 -0700

que componente esta roto, solo hecha agua pero no se muebe

⟐ Answered febrero 10, 2026 at 10:29 GMT-7

Amana Washing Machine: Mi lavadora no lava,solo hace el centrifugado

Fri, 02 Aug 2024 23:39:46 -0700

Tengo un problema con mi lavadora,no lava solo realiza el centrifugado,ya revise el sensor de la tapa pero aún así no lava

⟐ Commented agosto 02, 2024 at 23:39 GMT-7

Amana Washing Machine NTW4516FW: I need to get the screws to attach the pulley cover

Sat, 15 Aug 2026 07:20:23 -0700

What are the screws?

⟐ Answered agosto 15, 2026 at 7:20 GMT-7

Amana Washing Machine NTW4516FW: Stuck on final rinse, LED flashing

Tue, 07 Jul 2026 00:38:24 -0700

Hello. I was originally getting a flashing LED for Final Spin and it wouldn't progress past it.

I would try to press drain/spin and it will only drain a bit and then not spin.

I have replaced the shift actuator, splutch kit, and capacitor(even though old one was good).

After replacing the parts I have done a recalibration and the issue still persisted.

I went into Diag mode and got a code F7E1 for Basket speed. During Auto test it went through it completely fine.

In manual mode it everything seems to work except for it being on "LowSpin/HighSpin" where I get nothing. Agitation mode works fine. The windings of the motor were in spec as I was going through trouble shooting steps.

I'm currently at the point where I'm trying to check voltage on J12 / J2 connector. My multimeter isn't thin enough to backprobe the 4 pin J12 connector.

What else can I do to fix this washer?

Also when roommates use the washer it's sometimes unbalanced and clunks until we stop the cycle and rebalance the load. Tub suspension bolts seem intact by the way

⟐ Commented julio 07, 2026 at 0:38 GMT-7

Amana Washing Machine: My water keeps getting out when washing

Sun, 05 Jul 2026 11:55:01 -0700

Water keeps coming out when washing

⟐ Answered julio 05, 2026 at 11:55 GMT-7

Amana Washing Machine: lid lock bypass procedure

Tue, 16 Jun 2026 10:31:43 -0700

Amana top load washer has a 4 wire lock switch. I connect blue & white wires it will start to fill then stops & red lock light starts blinking ,then fill light blinks , that is all it does.

⟐ Commented junio 16, 2026 at 10:31 GMT-7

Amana Washing Machine NTW4516FW: Amana NTW4516FW Washer does not advance to rinse cycle

Mon, 08 Jun 2026 11:51:24 -0700

The washer fills, agitates, and spins. Then it thinks it is done and shuts off. The washer needs to be set to a manual rinse cycle after washing. It also seems to have issues with auto sense. Water level seems deeper than necessary, so that washing small loads is not water efficient.

⟐ Commented junio 08, 2026 at 11:51 GMT-7

Amana Washing Machine NTW4516FW: Macine Not agitating properley

Sun, 19 Apr 2026 12:42:59 -0700

The dogs on the top are in good shape but it is not agitating

Amana Washing Machine: Power switch is broken

Mon, 30 Mar 2026 04:56:05 -0700

Power switch is broken

Amana Washing Machine NTW4516FW: Clicking noise during wash cycle

Mon, 01 Dec 2025 00:30:34 -0700

my washer was making a grinding noise so I recently put a new splutch kit on. Now its making a clicking noise during wash cycle.

⟐ Commented diciembre 01, 2025 at 0:30 GMT-7

Amana Washing Machine: Comes on all by its self

Fri, 21 Nov 2025 00:45:45 -0700

My washer sounds like it's trying turn on but no one put anything in it or messed with washer in any way

⟐ Answer edited noviembre 21, 2025 at 0:45 GMT-7

Amana Washing Machine: Amana Tandem 7300 Washer F6E1 Error - Not Spinning

Mon, 07 Apr 2025 01:54:23 -0700

Hi All,

I cleaned out the pump catch on my Tandem 7300 after it got the usual beep error due to a heavy load that wouldn't drain in time. Lots of junk removed. Power off machine for ten minutes. Plugged it in and the water drained and door opened.

Now - whenever I try to start a wash - or any cycle - the door locks and it sits for a while - no initial spin of the tub as before - and nothing happens until the beeping starts - code is an F6E1.

I found a Whirlpool service manual online ( see https://www.whirlpool.com/content/dam/gl... ) which was really helpful as it allowed me to run diagnostics. The lock, then water fill, then water drain cycles seem to work then beeping starts. Same error. I clear the error and repeated the diagnostics a few time - same results.

I took off the top and back of the machine - the tub belt is fine and the motor spins freely. The motor does nothing during the diagnostics - doesn't make any noise or try to spin.

I re-seated all cabled everywhere I could - to the motor, control panel, water valve switches on hot and cold lines and what looks like the water detector at the bottom of the tub enclosure - still I get the same error during diagnostics - and no cycles will start normally past the initial lock of the door.

Can anyone advise on what this might be? I can't find a service manual for the exact model and the user manual is intentionally vague - but the service manual for newer front-loaders I found suggests the problem is the HMI - Human-Machine Interface - which I think means the front panel?

Thanks for any and all assistance!

Mike

Hello - An update:

The service manual indicated that the problem was most likely the Motor Control Unit (MCU) so I ordered a replacement. The replacement came and I installed it - the problem still exists. The only difference is now I hear a click when the motor should run - after the normal door lock click (not the same click - this click comes from under the tub - either the MCU or the motor. But, the motor still doesn't spin.

So - any cycle that I run I get the same as before except I'm hearing an click after the door lock - then after a few minutes the beeps start with the F6E1 error again.

When I run diagnostics - all the cycles work up to the tub spin test - again, the same error.

Any suggestions here would be greatly appreciated.

Mike

⟐ Commented abril 07, 2025 at 1:54 GMT-7

Amana Washing Machine NTW4516FW: Unit doesn't fill with cold water and will not advance to spin cycle

Thu, 21 Nov 2024 01:09:11 -0700

My washer will not fill all the way and time out if I use anything other than the "warm" option for water temperature. Everytime I check on a load the clothes will be wet and the light will be on rinse.

⟐ Answer edited noviembre 21, 2024 at 1:09 GMT-7

Amana Washing Machine: Why did my washer lid lock

Sun, 07 Jan 2024 17:51:56 -0700

A load of wash was done and all 6 lights are out and the lid is locked

⟐ Commented enero 07, 2024 at 17:51 GMT-7

Amana Washing Machine: Amana doesn’t spin or wash

Tue, 12 Dec 2023 23:06:28 -0700

How do I fix my Amana washing machine that doesn’t wash it spin?

⟐ Commented diciembre 12, 2023 at 23:06 GMT-7

Amana Washing Machine NTW4516FW: Not finishing the wash drain rinse

Thu, 07 Dec 2023 02:26:10 -0700

My washer when I start it will start to run water then stops and shuts off. If I leave it it will continue after being shut off but never drains?

⟐ Answered diciembre 07, 2023 at 2:26 GMT-7

Amana Washing Machine NTW4516FW: Lid lock will not unlock

Fri, 10 Nov 2023 10:45:25 -0700

The lid lock on my washer was broken and would not lock. I replaced it. When I lowered the lid while reassembling it locked and now will not unlock. I have been on YouTube and tried self test, diagnostic( no error shows) The light may be on or off but does not unlock? Any more ideas? I took it back apart once to confirm it was installed correctly. Manually unlocked it, but when I reassemble again the lid locks automatically as though it has to do with positioning??

Thanks, Katie

Amana Washing Machine: Amana Tandem 7300 Water out pump keeps blowing

Fri, 20 Dec 2024 11:43:50 -0700

Hi there! I have a tandem 7300. The error code for the water drainage comes up (along with a tub full of water) every time I was a load and it never finishes the cycle. Even on drain and spin I manually drain it, start that option but when I come back the tub is filled with water??

So I bought a new pump, replaced it, and it worked for like 6 loads. It then smelt like an electrical fire and the pump burned out. I bought a new one and this worked for 2 loads. What could be the issue????

⟐ Edited diciembre 20, 2024 at 11:43 GMT-7

Amana Washing Machine NTW4516FW: Washer will not continue to ANY cycle

Wed, 05 Jul 2023 09:42:23 -0700

I am just searching for a little confirmation on my troubleshooting before I go and spend $200 for a timer. The machine will fill, drain, and spin correctly within any given cycle but it will not continue into the next cycle regardless of what it is.

Could there be another possible cause of this problem that I could test?