Introducción

The guide takes place from the Camera Lens Assembly guide.

Partes

No se requieren partes.

Locate the memory card and battery card latch on the bottom of the camera.
  • Locate the memory card and battery card latch on the bottom of the camera.

  • Slide the latch to the open position.

Agregar Comentario

Open the battery latch, and slide the battery release lever to the right.
  • Open the battery latch, and slide the battery release lever to the right.

Agregar Comentario

Remove the battery from the camera.
  • Remove the battery from the camera.

Agregar Comentario

Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.
  • Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

  • Use this screwdriver for all screws in the device.

Agregar Comentario

Remove the 3.15 mm screw on the left side of the camera.
  • Remove the 3.15 mm screw on the left side of the camera.

Agregar Comentario

Remove the left side casing. Remove the left side casing.
  • Remove the left side casing.

Agregar Comentario

Remove the two 3.15 mm screws on the right side of the camera.
  • Remove the two 3.15 mm screws on the right side of the camera.

Agregar Comentario

Remove the bottom right panel.
  • Remove the bottom right panel.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Gently remove the back casing. Start at the bottom and carefully pry towards the top to get this piece free.
  • Gently remove the back casing.

  • Start at the bottom and carefully pry towards the top to get this piece free.

Agregar Comentario

Remove the two black 5.35 mm screws that hold in the front faceplate. There may be a third screw the the right of the lens assembly.
  • Remove the two black 5.35 mm screws that hold in the front faceplate.

  • There may be a third screw the the right of the lens assembly.

Agregar Comentario

Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery.
  • Carefully remove the upper assembly, which houses the buttons and the flash battery.

Agregar Comentario

Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.
  • Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

Agregar Comentario

Remove the three black 5mm screws attached to the lens frame. Remove the three black 5mm screws attached to the lens frame.
  • Remove the three black 5mm screws attached to the lens frame.

Agregar Comentario

Remove the lens frame.
  • Remove the lens frame.

Agregar Comentario

Lift out the circuit board as shown.
  • Lift out the circuit board as shown.

Agregar Comentario

Lift the two black latches that hold the connector ribbons in place. Disconnect the two ribbons.
  • Lift the two black latches that hold the connector ribbons in place.

  • Disconnect the two ribbons.

Agregar Comentario

Remove the lens assembly as shown.
  • Remove the lens assembly as shown.

Agregar Comentario

Remove four 4mm screws from the lens assembly.
  • Remove four 4mm screws from the lens assembly.

Agregar Comentario

Carefully turn over the assembly. Carefully turn over the assembly.
  • Carefully turn over the assembly.

Agregar Comentario

Remove the Fixed Frame Unit by separating it from the assembly. Remove the Direct Frame Unit from the assembly.
  • Remove the Fixed Frame Unit by separating it from the assembly.

  • Remove the Direct Frame Unit from the assembly.

Agregar Comentario

Remove the 1st lens frame from the lens assembly.
  • Remove the 1st lens frame from the lens assembly.

Agregar Comentario

Detach the 2nd Frame Unit from the assembly.
  • Detach the 2nd Frame Unit from the assembly.

Agregar Comentario

Remove the 4mm screw from the lens housing.
  • Remove the 4mm screw from the lens housing.

Agregar Comentario

Separate the lens housing.
  • Separate the lens housing.

  • Replace the lens by gently prying away from the assembly.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Caleb Fink

Miembro Desde 11/10/10

186 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 9-22, Regan Fall 2010 Miembro de Cal Poly, Team 9-22, Regan Fall 2010

CPSU-REGAN-F10S9G22

4 Miembros

8 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 4

Últimos 30 Días: 12

Todo El Tiempo: 11,859