Partes

No se requieren partes.

Flip the mouse over and peel off the stickers on the perimeter of the bottom of the mouse
  • Flip the mouse over and peel off the stickers on the perimeter of the bottom of the mouse

my mouse sucks i peeled off the tape and there is a layer of something blocking the the screw it is a gaming mouse and i got it 2 weeks ago

Nathan Swercewski - Contestar

Use the Phillips #1 screwdriver to unscrew the six round head screws on the bottom of the mouse. Those marked with squares are 9 mm in length, the rest are 5 mm in length. Use the Phillips #1 screwdriver to unscrew the six round head screws on the bottom of the mouse. Those marked with squares are 9 mm in length, the rest are 5 mm in length.
  • Use the Phillips #1 screwdriver to unscrew the six round head screws on the bottom of the mouse. Those marked with squares are 9 mm in length, the rest are 5 mm in length.

Agregar Comentario

Grab the top shell of the mouse and lift up to remove. Grab the top shell of the mouse and lift up to remove. Grab the top shell of the mouse and lift up to remove.
  • Grab the top shell of the mouse and lift up to remove.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
The capacitors on this board can release stored electrical energy if touched.
  • The capacitors on this board can release stored electrical energy if touched.

  • Touch your capacitor discharge tool to the capacitor leads on the board to release the stored energy. If leads are inaccessible, wait until you've removed the board from the mouse body.

Agregar Comentario

To remove the white wire connector on the bottom board, use a spudger underneath the white plug and pop it out (this disconnects the upper board from the lower board). To remove the white wire connector on the bottom board, use a spudger underneath the white plug and pop it out (this disconnects the upper board from the lower board).
  • To remove the white wire connector on the bottom board, use a spudger underneath the white plug and pop it out (this disconnects the upper board from the lower board).

Agregar Comentario

Remove the 5 mm round head screw holding the middle piece to the top piece.
  • Remove the 5 mm round head screw holding the middle piece to the top piece.

  • The outermost shell will now separate from the middle structure.

Agregar Comentario

Using the Phillips #1 screwdriver, unscrew the 5 mm black flat head screw that's securing the scroll wheel cage.
  • Using the Phillips #1 screwdriver, unscrew the 5 mm black flat head screw that's securing the scroll wheel cage.

Agregar Comentario

Pinch the cage to release snaps. You can now pull the cage off. Pinch the cage to release snaps. You can now pull the cage off.
  • Pinch the cage to release snaps. You can now pull the cage off.

Agregar Comentario

Remove the screw holding the circuit board down.
  • Remove the screw holding the circuit board down.

  • The board will now pop off easily.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

David

Miembro Desde 16/01/13

647 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 18-36, Regan Winter 2013 Miembro de Cal Poly, Team 18-36, Regan Winter 2013

CPSU-REGAN-W13S18G36

3 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 3

Últimos 30 Días: 4

Todo El Tiempo: 466