Partes

No se requieren partes.

Unlatch the battery by pushing outward on both latches.
  • Unlatch the battery by pushing outward on both latches.

Agregar Comentario

Slide battery out.
  • Slide battery out.

Agregar Comentario

Remove the five "F2" screws with a Phillips #0 screwdriver.
  • Remove the five "F2" screws with a Phillips #0 screwdriver.

Agregar Comentario

Insert the plastic opening tool above the F1 key. Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.
  • Insert the plastic opening tool above the F1 key.

  • Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.

Agregar Comentario

Find the screws above the F1 and INS keys. Unscrew both screws with a Phillips #0 screwdriver.
  • Find the screws above the F1 and INS keys.

  • Unscrew both screws with a Phillips #0 screwdriver.

Agregar Comentario

Slowly lift the top edge of the keyboard out with your fingers. The ribbon cable located on the back of the keyboard will become accessible.
  • Slowly lift the top edge of the keyboard out with your fingers.

  • The ribbon cable located on the back of the keyboard will become accessible.

Agregar Comentario

Locate the black ribbon cable flap. Detach flap with plastic opening tool.  The ribbon cable will become free.
  • Locate the black ribbon cable flap.

  • Detach flap with plastic opening tool. The ribbon cable will become free.

Agregar Comentario

Your keyboard has now been successfully removed.
  • Your keyboard has now been successfully removed.

Agregar Comentario

Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.
  • Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.

Agregar Comentario

Locate and remove the circled screw with a Phillips #0 screwdriver. Locate and remove the circled screw with a Phillips #0 screwdriver.
  • Locate and remove the circled screw with a Phillips #0 screwdriver.

Agregar Comentario

Use the plastic opening tool to pry the CD/DVD drive out of the frame.
  • Use the plastic opening tool to pry the CD/DVD drive out of the frame.

Agregar Comentario

Gently remove the CD/DVD drive from the laptop body.
  • Gently remove the CD/DVD drive from the laptop body.

Agregar Comentario

Remove the circled screws with Phillips #0 screwdriver. Remove the circled screws with Phillips #0 screwdriver.
  • Remove the circled screws with Phillips #0 screwdriver.

Agregar Comentario

Remove these screws from the underside of the laptop with Phillips #0 screwdriver.
  • Remove these screws from the underside of the laptop with Phillips #0 screwdriver.

Agregar Comentario

Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.
  • Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.

  • Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.

Agregar Comentario

Remove the circled screw with a Phillips #0 screwdriver.
  • Remove the circled screw with a Phillips #0 screwdriver.

Agregar Comentario

Detach the 3 marked cables by pulling them out with you fingers as shown.
  • Detach the 3 marked cables by pulling them out with you fingers as shown.

  • This may require some force. They do not come out easily.

Agregar Comentario

Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.
  • Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.

Agregar Comentario

Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.
  • Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.

Agregar Comentario

Remove the circled motherboard screws with a Phillips #0 Scewdriver.
  • Remove the circled motherboard screws with a Phillips #0 Scewdriver.

  • Disconnect this ribbon cable.

Agregar Comentario

Remove these screws with a Phillips #0 screwdriver.
  • Remove these screws with a Phillips #0 screwdriver.

Agregar Comentario

Detach the display cable by gently pulling it out with your fingers.
  • Detach the display cable by gently pulling it out with your fingers.

Agregar Comentario

Remove the motherboard from the left side by gently lifting the left side upward. The boxed volume control may snag on the laptop frame when pulling the motherboard out.
  • Remove the motherboard from the left side by gently lifting the left side upward.

  • The boxed volume control may snag on the laptop frame when pulling the motherboard out.

Agregar Comentario

The motherboard has now been removed from laptop.
  • The motherboard has now been removed from laptop.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Equipo

Cal Poly, Team 4-3, Regan Spring 2011 Miembro de Cal Poly, Team 4-3, Regan Spring 2011

CPSU-REGAN-S11S4G3

5 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 3

Últimos 30 Días: 11

Todo El Tiempo: 11,146