Introducción

This guide may be useful for fixing dead pixels, cracked screens, and other problems with the display. You will need the iFixit plastic opening tool, a Phillips #1 screw driver, and your new Toshiba Satellite A75-S226 Display Assembly.

Remove the 5.75 mm screw from the cover panel. Turn the laptop over with the screen facing down.
  • Remove the 5.75 mm screw from the cover panel.

  • Turn the laptop over with the screen facing down.

Agregar Comentario

Lift up the cover panel using a plastic opening tool.
  • Lift up the cover panel using a plastic opening tool.

Agregar Comentario

Remove the 5.64 mm screw from the bottom of the crossing bar. Remove the crossing bar.
  • Remove the 5.64 mm screw from the bottom of the crossing bar.

  • Remove the crossing bar.

Agregar Comentario

Use a plastic opening tool to disconnect the black and white antenna cable's connectors from the Wi-Fi card. Note that the black wire is connected to the port that is labeled main.
  • Use a plastic opening tool to disconnect the black and white antenna cable's connectors from the Wi-Fi card.

    • Note that the black wire is connected to the port that is labeled main.

Agregar Comentario

Use fingers to push the clips away from memory card. Use fingers to push the clips away from memory card.
  • Use fingers to push the clips away from memory card.

Agregar Comentario

Use fingers to remove the Wi-Fi card.
  • Use fingers to remove the Wi-Fi card.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Use the plastic opening tool to lift up the top panel all the way along the keyboard until it loosens. It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge. It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge.
  • Use the plastic opening tool to lift up the top panel all the way along the keyboard until it loosens.

  • It may be helpful to first pry at the rear of the hinge covers (not shown) to release them. Then Insert the plastic opening tool underneath the top panel's sides and then front edge.

Agregar Comentario

Remove the top panel by popping the panel out the top left socket, then do the same with the right side. Remove the top panel by popping the panel out the top left socket, then do the same with the right side.
  • Remove the top panel by popping the panel out the top left socket, then do the same with the right side.

Agregar Comentario

Remove the two 3.67 mm screws from the top corners of the keyboard. Remove the two 3.67 mm screws from the top corners of the keyboard. Remove the two 3.67 mm screws from the top corners of the keyboard.
  • Remove the two 3.67 mm screws from the top corners of the keyboard.

Agregar Comentario

Use fingers to lift up the keyboard from the top.
  • Use fingers to lift up the keyboard from the top.

  • Do not try to remove the keyboard completely because it is still attached to the motherboard.

Agregar Comentario

Remove the cable connecting the keyboard with the motherboard. Be aware of the locking tabs on each side of the ribbon-cable connector—they slide back about 2mm to free the cable. Lift up and remove the keyboard.
  • Remove the cable connecting the keyboard with the motherboard.

  • Be aware of the locking tabs on each side of the ribbon-cable connector—they slide back about 2mm to free the cable.

  • Lift up and remove the keyboard.

Agregar Comentario

Remove the 3.76mm screw from the ground wire. Remove the 3.76mm screw from the ground wire.
  • Remove the 3.76mm screw from the ground wire.

Agregar Comentario

Use the plastic opening tool to remove the wire. Use the plastic opening tool to remove the wire.
  • Use the plastic opening tool to remove the wire.

Agregar Comentario

Gently pull the black and white wires out of the upper case. Do not pull the wire too much, or you can damage the wire.
  • Gently pull the black and white wires out of the upper case.

  • Do not pull the wire too much, or you can damage the wire.

Agregar Comentario

Remove the 8.6 mm screw on left side of upper case.
  • Remove the 8.6 mm screw on left side of upper case.

Agregar Comentario

Remove two 8.6 mm screws on the back corners of the laptop. Remove two 8.6 mm screws on the back corners of the laptop.
  • Remove two 8.6 mm screws on the back corners of the laptop.

Agregar Comentario

Lift up the display assembly to remove it.
  • Lift up the display assembly to remove it.

one of the 14 screws identified in the diagram of step 25 was previously removed with the CD drive

Steve - Contestar

Conclusión

Replace the old display assembly with your new assembly. To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Garrett Gudgel

Miembro Desde 05/10/10

714 Reputación

13 Guías creadas

Equipo

Cal Poly, Team 4-43, Amido Fall 2010 Miembro de Cal Poly, Team 4-43, Amido Fall 2010

CPSU-AMIDO-F10S4G43

5 Miembros

13 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 5

Todo El Tiempo: 6,101