Saltar al contenido principal

Sceptre X9 Komodo VII Power Supply Unit Replacement

Qué necesitas

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: paso 1, imagen 1 de 1
    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 2, imagen 1 de 1
    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: paso 3, imagen 1 de 1
    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

  4. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 4, imagen 1 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 4, imagen 2 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 4, imagen 3 de 3
    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 5, imagen 1 de 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 5, imagen 2 de 2
    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: paso 6, imagen 1 de 1
    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 7, imagen 1 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 7, imagen 2 de 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 7, imagen 3 de 3
    • Unplug the seven connections from the power supply unit by gently pulling on them.

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 8, imagen 1 de 1
    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 9, imagen 1 de 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: paso 9, imagen 2 de 2
    • Lift the power supply unit straight up to remove it from the back panel.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Equipo

Cal Poly, Team 16-56, Forte Fall 2012 Miembro de Cal Poly, Team 16-56, Forte Fall 2012

CPSU-FORTE-F12S16G56

5 Miembros

13 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 5

Todo El Tiempo: 664