Introducción

This guide will provide a step-by-step procedure for replacing the OLED screen in your Samsung Rogue. This is one of the more difficult repair guides because it requires a lot of disassembling.

Before disassembling your Samsung Rogue, make sure it is powered off. With your thumbs, push down on the back cover of your phone and slide it away from the camera.
  • Before disassembling your Samsung Rogue, make sure it is powered off.

  • With your thumbs, push down on the back cover of your phone and slide it away from the camera.

Agregar Comentario

You can now remove the battery by prying it up with your finger. You can now remove the battery by prying it up with your finger.
  • You can now remove the battery by prying it up with your finger.

Agregar Comentario

Use a plastic opening tool to carefully pry the back cover surrounding the camera up from the phone.
  • Use a plastic opening tool to carefully pry the back cover surrounding the camera up from the phone.

Agregar Comentario

Remove the five 3.4mm Philips screws securing the backing of the phone.
  • Remove the five 3.4mm Philips screws securing the backing of the phone.

Agregar Comentario

Use a plastic opening tool to carefully pry off the back cover. Make sure you are prying along the edge and not between the two halves of the phone that slide away from each other. Be careful to not drop the volume changing piece, for it can easily slip out.
  • Use a plastic opening tool to carefully pry off the back cover.

  • Make sure you are prying along the edge and not between the two halves of the phone that slide away from each other.

  • Be careful to not drop the volume changing piece, for it can easily slip out.

Agregar Comentario

Remove the two 3.45 mm Philips screws below the white sticker.
  • Remove the two 3.45 mm Philips screws below the white sticker.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Carefully lift the motherboard up from the bottom edge. The film of wires is still attached to the motherboard, so do not completely remove the motherboard just yet or you may damage it.
  • Carefully lift the motherboard up from the bottom edge.

  • The film of wires is still attached to the motherboard, so do not completely remove the motherboard just yet or you may damage it.

Agregar Comentario

Use a plastic opening tool to disconnect the film from the motherboard. Use a plastic opening tool to disconnect the film from the motherboard.
  • Use a plastic opening tool to disconnect the film from the motherboard.

Agregar Comentario

Remove the eight 1.7mm Philips screws above the keyboard.
  • Remove the eight 1.7mm Philips screws above the keyboard.

Agregar Comentario

Carefully remove the keyboard frame from the sliding mechanisms underneath.
  • Carefully remove the keyboard frame from the sliding mechanisms underneath.

Agregar Comentario

Remove the five 3.0mm Philips screws around the outside of the sliding mechanisms.
  • Remove the five 3.0mm Philips screws around the outside of the sliding mechanisms.

Agregar Comentario

Use a plastic opening tool to pry off the upper slide plate. Be careful of the film of wires when taking off the upper slide plate. Be careful of the film of wires when taking off the upper slide plate.
  • Use a plastic opening tool to pry off the upper slide plate.

  • Be careful of the film of wires when taking off the upper slide plate.

Agregar Comentario

Use tweezers to open the four black gates by putting them in the "up" position. With the same tweezers, carefully pull out the orange strips from the four specified gates. With the same tweezers, carefully pull out the orange strips from the four specified gates.
  • Use tweezers to open the four black gates by putting them in the "up" position.

  • With the same tweezers, carefully pull out the orange strips from the four specified gates.

Agregar Comentario

Using tweezers, gently remove the bottom orange strip from the device Using tweezers, gently remove the bottom orange strip from the device
  • Using tweezers, gently remove the bottom orange strip from the device

Agregar Comentario

In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside. In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside.
  • In this procedure, the rubber function key pad can easily fall out, so it would be best to take it out and set it safely aside.

Agregar Comentario

Starting at the top, use a plastic opening tool to pry open the protective screen on the front of the phone. One of the strips you pulled out of a gate from a previous step is attached to the screen at the bottom. Be careful not to damage it when you are taking off the screen. The protective screen is glued underneath the edges, so it will be a little more difficult to get off.
  • Starting at the top, use a plastic opening tool to pry open the protective screen on the front of the phone.

  • One of the strips you pulled out of a gate from a previous step is attached to the screen at the bottom. Be careful not to damage it when you are taking off the screen.

  • The protective screen is glued underneath the edges, so it will be a little more difficult to get off.

  • Keep your hand underneath the OLED screen at all times because it easily falls out once the protective screen detaches.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Equipo

Cal Poly, Team 7-32, Maness Spring 2012 Miembro de Cal Poly, Team 7-32, Maness Spring 2012

CPSU-MANESS-S12S7G32

4 Miembros

16 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 9

Todo El Tiempo: 1,855