Introducción

This guide will show you how to replace your microphone.

Slide your fingernail into the slit at the bottom of the phone to remove the back cover.
  • Slide your fingernail into the slit at the bottom of the phone to remove the back cover.

Agregar Comentario

Place your finger in either of the bottom corner of the battery slot and lift to remove the battery.
  • Place your finger in either of the bottom corner of the battery slot and lift to remove the battery.

Agregar Comentario

Remove six 5 mm Phillips #0 screws from the back of the phone.
  • Remove six 5 mm Phillips #0 screws from the back of the phone.

Agregar Comentario

Insert a plastic opening tool into the seam between the back case and the rest of the phone.
  • Insert a plastic opening tool into the seam between the back case and the rest of the phone.

  • Working along the seam, pry the back from the phone.

Agregar Comentario

Remove the two remaining 3.75 mm Phillips screws.
  • Remove the two remaining 3.75 mm Phillips screws.

Agregar Comentario

Firmly grip the black lever with tweezers Use the tweezers to flip the black lever up so that it is perpendicular to the motherboard.
  • Firmly grip the black lever with tweezers

  • Use the tweezers to flip the black lever up so that it is perpendicular to the motherboard.

Agregar Comentario

Carefully use the tweezers to slide the black ZIF cable out of the socket.
  • Carefully use the tweezers to slide the black ZIF cable out of the socket.

Agregar Comentario

Use the tweezers to unclip the black connector as shown. Use the tweezers to unclip the black connector as shown.
  • Use the tweezers to unclip the black connector as shown.

Agregar Comentario

Use the tweezers to unclip the orange flexible circuit board from the side of the phone. Use the tweezers to unclip the orange flexible circuit board from the side of the phone.
  • Use the tweezers to unclip the orange flexible circuit board from the side of the phone.

Agregar Comentario

Use the tweezers to unclip the other orange, smaller flexible circuit board.
  • Use the tweezers to unclip the other orange, smaller flexible circuit board.

  • Work carefully. This is a very delicate part of the phone that can easily be broken.

Agregar Comentario

Slide one side of the tweezers underneath the red and blue wires of the capacitor. Carefully apply pressure away from the phone to lift.
  • Slide one side of the tweezers underneath the red and blue wires of the capacitor.

  • Carefully apply pressure away from the phone to lift.

Agregar Comentario

Carefully tilt the motherboard up from the back of the phone. Don't remove the motherboard completely. There is one more clip on the backside of the motherboard that needs to be removed.
  • Carefully tilt the motherboard up from the back of the phone.

  • Don't remove the motherboard completely. There is one more clip on the backside of the motherboard that needs to be removed.

  • Use tweezers to unclip the black connector.

Agregar Comentario

Hold the phone by the black plastic at the ends and slightly bend them down so that the middle of the phone is the highest point. Apply pressure slowly until the until the grey portion pops off. Hold the phone by the black plastic at the ends and slightly bend them down so that the middle of the phone is the highest point. Apply pressure slowly until the until the grey portion pops off.
  • Hold the phone by the black plastic at the ends and slightly bend them down so that the middle of the phone is the highest point. Apply pressure slowly until the until the grey portion pops off.

Agregar Comentario

Insert the tweezers into the hole as shown so that they are wedged between the LCD and grey plastic. Slide the tweezers underneath the LCD, around the three silver edges, until the entire display is lifted from grey plastic. Slide the tweezers underneath the LCD, around the three silver edges, until the entire display is lifted from grey plastic.
  • Insert the tweezers into the hole as shown so that they are wedged between the LCD and grey plastic.

  • Slide the tweezers underneath the LCD, around the three silver edges, until the entire display is lifted from grey plastic.

Agregar Comentario

Find the rubber microphone backing on the bottom of the back of the front cover as shown in the picture. Use tweezers to pluck the microphone from the casing. Find the rubber microphone backing on the bottom of the back of the front cover as shown in the picture. Use tweezers to pluck the microphone from the casing.
  • Find the rubber microphone backing on the bottom of the back of the front cover as shown in the picture. Use tweezers to pluck the microphone from the casing.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Collin Gordon

Miembro Desde 08/04/13

45 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 17-1, Regan Spring 2013 Miembro de Cal Poly, Team 17-1, Regan Spring 2013

CPSU-REGAN-S13S17G1

4 Miembros

18 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 180