Introducción

Flash bulb soldered to circuit board with capacitor, so it is not possible to only replace flash bulbs.

Remove the six external screws from the camera using a Phillips #0 screwdriver. After the screws has been removed, the bottom of the back half of the external case should be loosened from the camera. Be careful, make sure you don't lose the screws.
  • Remove the six external screws from the camera using a Phillips #0 screwdriver.

  • After the screws has been removed, the bottom of the back half of the external case should be loosened from the camera.

  • Be careful, make sure you don't lose the screws.

Agregar Comentario

Open the battery cover that's located on the bottom right side of the camera and carefully remove the battery. Open the battery cover that's located on the bottom right side of the camera and carefully remove the battery.
  • Open the battery cover that's located on the bottom right side of the camera and carefully remove the battery.

Agregar Comentario

Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera. Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera. Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera.
  • Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera.

Agregar Comentario

Carefully squeeze the top right corner of the camera and pry off the external cover.
  • Carefully squeeze the top right corner of the camera and pry off the external cover.

  • If you hear a "cracking" sound. This is normal.

  • Continue to pull the external cover and it will come off cleanly.

  • Be cautious of the flash capacitor. It carries an electrical charge, that may give you an unpleasant shock.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Carefully pull off the back cover, parts behind the back of the case might fall out.
  • Carefully pull off the back cover, parts behind the back of the case might fall out.

Agregar Comentario

Remove the screws holding the circuit board.
  • Remove the screws holding the circuit board.

  • After you remove the screws, carefully remove the circuit board.

Agregar Comentario

Remove the front cover, it comes off easily. Buttons might fall out when you remove the front cover.
  • Remove the front cover, it comes off easily.

  • Buttons might fall out when you remove the front cover.

Agregar Comentario

Face camera towards you.
  • Face camera towards you.

  • Remove the two screws from circuit board on the left side of the lens.

Agregar Comentario

Carefully hold up the circuit board, while it's still connected to the camera.
  • Carefully hold up the circuit board, while it's still connected to the camera.

  • Remove all five screws that's on top of the camera.

Agregar Comentario

Carefully push up the top of the circuit board. Pull up flash circuit board from top of camera. Pull up flash circuit board from top of camera.
  • Carefully push up the top of the circuit board.

  • Pull up flash circuit board from top of camera.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Adriel

Miembro Desde 15/04/10

111 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 6-17, Maness Spring 2010 Miembro de Cal Poly, Team 6-17, Maness Spring 2010

CPSU-MANESS-S10S6G17

4 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 7

Todo El Tiempo: 3,816