Partes

No se requieren partes.

Open the tray by pressing the eject button Remove the DVD tray faceplate by pushing the faceplate up off of the tray. Remove the DVD tray faceplate by pushing the faceplate up off of the tray.
  • Open the tray by pressing the eject button

  • Remove the DVD tray faceplate by pushing the faceplate up off of the tray.

Agregar Comentario

Press the eject button to insert the tray
  • Press the eject button to insert the tray

  • After the tray is closed unplug DVD player

Agregar Comentario

Unscrew the 3 screws in the back.
  • Unscrew the 3 screws in the back.

Agregar Comentario

Pull the outer case upward and then towards you. Pull the outer case upward and then towards you.
  • Pull the outer case upward and then towards you.

Agregar Comentario

There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate. There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate. There are six symmetrically placed tabs holding in the front faceplate.  Unhook these six tabs to loosen the faceplate.
  • There are six symmetrically placed tabs holding in the front faceplate. Unhook these six tabs to loosen the faceplate.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously. Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously.
  • Pull off front faceplate. This may take a couple of tries to get all six tabs unhooked simultaneously.

Agregar Comentario

Locate the white clip that attaches the cord to the motherboard Grasp clip and squeeze to release Lift up and remove power cord
  • Locate the white clip that attaches the cord to the motherboard

  • Grasp clip and squeeze to release

  • Lift up and remove power cord

  • Slide cord mount from outer case

Agregar Comentario

Remove the three screws holding in the DVD tray Remove the three screws holding in the DVD tray Remove the three screws holding in the DVD tray
  • Remove the three screws holding in the DVD tray

Agregar Comentario

Remove the power cord and first two ribbons by pulling them directly out of their sockets. Remove the power cord and first two ribbons by pulling them directly out of their sockets.
  • Remove the power cord and first two ribbons by pulling them directly out of their sockets.

Agregar Comentario

Gently lift the DVD tray off of the motherboard. Gently lift the DVD tray off of the motherboard.
  • Gently lift the DVD tray off of the motherboard.

Agregar Comentario

Spin the small gear shown to the right to begin opening the tray. There should be relatively little resistance in the gear. Spin the small gear shown to the right to begin opening the tray. There should be relatively little resistance in the gear.
  • Spin the small gear shown to the right to begin opening the tray. There should be relatively little resistance in the gear.

Agregar Comentario

Use your fingers to pull the shown tabs towards the sides of the tray, releasing the internal tray that contains the laser. Use your fingers to pull the shown tabs towards the sides of the tray, releasing the internal tray that contains the laser. Use your fingers to pull the shown tabs towards the sides of the tray, releasing the internal tray that contains the laser.
  • Use your fingers to pull the shown tabs towards the sides of the tray, releasing the internal tray that contains the laser.

Agregar Comentario

In order to remove the tray motor you must detach the small rubber band that runs between the two shown wheels. If the rubber band is improperly fitted onto one of the wheels or broken this is probably the cause of the tray not opening or closing.
  • In order to remove the tray motor you must detach the small rubber band that runs between the two shown wheels.

  • If the rubber band is improperly fitted onto one of the wheels or broken this is probably the cause of the tray not opening or closing.

Agregar Comentario

Flip over the tray and unscrew the two screws that attach the motor to the tray. Once completed the motor can be easily removed and replaced.
  • Flip over the tray and unscrew the two screws that attach the motor to the tray.

  • Once completed the motor can be easily removed and replaced.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Mitchell Hart

Miembro Desde 21/01/11

819 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 3-30, Regan Winter 2011 Miembro de Cal Poly, Team 3-30, Regan Winter 2011

CPSU-REGAN-W11S3G30

4 Miembros

8 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 12

Todo El Tiempo: 4,274