Introducción

Removing the power supply of the Power Mac G4.

The handle to open your computer is located on top of the right side panel.
  • The handle to open your computer is located on top of the right side panel.

Agregar Comentario

Grab the circular handle and pull outward. Grab the circular handle and pull outward.
  • Grab the circular handle and pull outward.

Agregar Comentario

Your computer is now open and ready for repair.
  • Your computer is now open and ready for repair.

Agregar Comentario

The optical drive is in the top left corner of the case.
  • The optical drive is in the top left corner of the case.

Agregar Comentario

There are four screws to be removed. The first screw can be seen in the first picture.
  • There are four screws to be removed.

  • The first screw can be seen in the first picture.

  • The remaining three screws can be seen in the second picture.

Agregar Comentario

Remove the optical drive by pulling the drive away from the front of the computer and out.
  • Remove the optical drive by pulling the drive away from the front of the computer and out.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Detach the two cables attached to the back of the drive.
  • Detach the two cables attached to the back of the drive.

  • The flat ribbon cable can be detached by pulling the silver tab. The multicolored cable can be removed by grasping the plastic connector on either side and pulling with substantial force.

Agregar Comentario

The hard drive is located in the back right corner of the case.
  • The hard drive is located in the back right corner of the case.

Agregar Comentario

Remove the flat ribbon cable by pulling with substantial force.
  • Remove the flat ribbon cable by pulling with substantial force.

Agregar Comentario

Remove the screw holding the hard drive to the computer.
  • Remove the screw holding the hard drive to the computer.

Agregar Comentario

Pull the drive up and out of the computer.
  • Pull the drive up and out of the computer.

Agregar Comentario

Remove the multicolored cable by grasping the plastic connector on either side and pulling with substantial force.
  • Remove the multicolored cable by grasping the plastic connector on either side and pulling with substantial force.

Agregar Comentario

The power supply is in the upper right corner of the case.
  • The power supply is in the upper right corner of the case.

Agregar Comentario

There is a total of four screws to be removed. The first three can be seen in the first picture.
  • There is a total of four screws to be removed.

  • The first three can be seen in the first picture.

  • The final screw can be seen in the second picture.

Agregar Comentario

There are three 2.5mm hex bolts located in the back of the computer that also need to be removed.
  • There are three 2.5mm hex bolts located in the back of the computer that also need to be removed.

  • A 3/32" Hex Key or Hex Driver is a bit small but may also work if gentle.

Agregar Comentario

Disconnect the power supply cables from the mother board by pressing in the tab on the back of the connector as shown.
  • Disconnect the power supply cables from the mother board by pressing in the tab on the back of the connector as shown.

This step can be done prior to Step 13.

dec59us - Contestar

Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!
  • Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!

  • Slide the power supply away from the back of the computer and pull it out carefully stringing the cables through the hole in the metal support.

Before sliding out the power supply make sure to disconnect the cable to the big fan by pressing in the small black tab on the back of the black connector!

7design - Contestar

Your power supply is now free from the enclosure and is ready to be replaced.
  • Your power supply is now free from the enclosure and is ready to be replaced.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

18 personas más completaron esta guía.

Jacob Garcia

Miembro Desde 28/01/10

483 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 14-41, Regan Winter 2010 Miembro de Cal Poly, Team 14-41, Regan Winter 2010

CPSU-REGAN-W10S14G41

4 Miembros

10 Guías creadas

I hate to say this, but that is not fixing the power supply but replacing the power supply with a new unit. i was hoping to fix it as mine blew and was hoping to revive it, but not luck on this end by the look of it. :(

Yannick Docq - Contestar

Thanks for the clear instructions to replace the power supply. I got my part on eBay for $29 (other online stores are charging $100-200+ for it) to doctor up an old G4, and it works like a charm now.

Brenna Jue - Contestar

Thank you so very much for these instructions. On my 733 G4 the blue front panel had to be removed to allow the DVD drive to exit from the front of the machine. I also had to remove the fan to allow the wires to exit with the power supply.

John - Contestar

Yet another G4 QuickSilver saved from the electronics recycler! In tandem with an eBay-listed refurbisher of my defunct PSU, it was brought back to life. Instructions were very clear.

dec59us - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 2

Últimos 7 Días: 12

Últimos 30 Días: 50

Todo El Tiempo: 25,104