Repara tus cosas Comunidad Tienda

HP Photosmart 935 Plastic Casing Replacement

Introducción

This guide will teach you how to install a new case on your HP Photosmart 935 camera. If your camera case is cracked or starting to come apart, this guide will help you replace it with a new one.

Qué necesitas

  1. HP Photosmart 935 Plastic Casing Replacement, Batteries: paso 1, imagen 1 de 2 HP Photosmart 935 Plastic Casing Replacement, Batteries: paso 1, imagen 2 de 2

    • Flip the camera over so the bottom of the camera is facing you.

    Traducir

    • Turn the mode dial to the OFF position.

    Traducir

  3. HP Photosmart 935 Plastic Casing Replacement: paso 3, imagen 1 de 2 HP Photosmart 935 Plastic Casing Replacement: paso 3, imagen 2 de 2

    • Slide the bottom cover in the direction of the arrow to open it.

    Traducir

  4. HP Photosmart 935 Plastic Casing Replacement: paso 4, imagen 1 de 1

    • Pull out the batteries.

    Traducir

  6. HP Photosmart 935 Plastic Casing Replacement, Plastic Casing: paso 5, imagen 1 de 1

    • Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.

    Traducir

  7. HP Photosmart 935 Plastic Casing Replacement: paso 6, imagen 1 de 2 HP Photosmart 935 Plastic Casing Replacement: paso 6, imagen 2 de 2

    • Remove the four 4.7 mm screws on the left side of the camera.

    Traducir

  8. HP Photosmart 935 Plastic Casing Replacement: paso 7, imagen 1 de 2 HP Photosmart 935 Plastic Casing Replacement: paso 7, imagen 2 de 2

    • Remove the four 4.7 mm screws on the opposite side of the camera.

    Traducir

  9. HP Photosmart 935 Plastic Casing Replacement: paso 8, imagen 1 de 3 HP Photosmart 935 Plastic Casing Replacement: paso 8, imagen 2 de 3 HP Photosmart 935 Plastic Casing Replacement: paso 8, imagen 3 de 3

    • Use your thumbs to pry the case apart.

    • It is easiest to pry the case apart if you start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a spudger or plastic opening tool to pry it open.

    Traducir

  10. HP Photosmart 935 Plastic Casing Replacement: paso 9, imagen 1 de 1

    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.

    Traducir

  11. HP Photosmart 935 Plastic Casing Replacement: paso 10, imagen 1 de 2 HP Photosmart 935 Plastic Casing Replacement: paso 10, imagen 2 de 2

    • While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out, pull the device out completely.

    • Use a firm grasp when removing the device from the case for stability and control.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 9 otros colaboradores

Clay Young

Miembro Desde 04/04/12

233 Reputación

2 Guías creadas

Insignias: 9

+ 6 más insignias

Equipo

Cal Poly, Team 15-13, Forte Spring 2012 Miembro de Cal Poly, Team 15-13, Forte Spring 2012

CPSU-FORTE-S12S15G13

5 Miembros

10 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 1

Todo El Tiempo: 1,726