Repara tus cosas Comunidad Tienda

Philips Norelco 5801XL Battery Replacement

Introducción

Use this guide to replace the rechargeable battery in the Philips Norelco 5801XL. The steps should be followed exactly as listed in the guide. Some soldering skills are required. Be sure to handle with care. For help with soldering: click here.

Qué necesitas

  1. Philips Norelco 5801XL Battery Replacement, Battery: paso 1, imagen 1 de 2 Philips Norelco 5801XL Battery Replacement, Battery: paso 1, imagen 2 de 2

    • Using a T8 torx screwdriver, remove both 2mm T8 screws.

    Traducir

  2. Philips Norelco 5801XL Battery Replacement: paso 2, imagen 1 de 2 Philips Norelco 5801XL Battery Replacement: paso 2, imagen 2 de 2

    • Using a plastic opening tool, separate the front housing from the back housing.

    • Carefully pull the housing apart.

    Traducir

  3. Philips Norelco 5801XL Battery Replacement: paso 3, imagen 1 de 3 Philips Norelco 5801XL Battery Replacement: paso 3, imagen 2 de 3 Philips Norelco 5801XL Battery Replacement: paso 3, imagen 3 de 3

    • Remove the plastic bracket using a plastic opening tool.

    • Pry from the inside of the bracket towards the outside of the housing to remove it.

    Traducir

  5. Philips Norelco 5801XL Battery Replacement: paso 4, imagen 1 de 1

    • Remove the two T8 2mm Philips screws holding onto the bracket over the charge port.

    • Remove the bracket. It will pull straight out.

    Traducir

  6. Philips Norelco 5801XL Battery Replacement: paso 5, imagen 1 de 1

    • Push in the charge port using the plastic opening tool.

    Traducir

  7. Philips Norelco 5801XL Battery Replacement: paso 6, imagen 1 de 1

    • Lift the circuit board upwards and fold it towards the head of the razor.

    • Do not break the contacts connecting the board to the motor.

    Traducir

  8. Philips Norelco 5801XL Battery Replacement: paso 7, imagen 1 de 3 Philips Norelco 5801XL Battery Replacement: paso 7, imagen 2 de 3 Philips Norelco 5801XL Battery Replacement: paso 7, imagen 3 de 3

    • Desolder the contacts where the battery connects to the circuit board.

    • Straighten the battery contacts and pull them through the opposite side of the circuit board.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 4 otros colaboradores

Ben Gibbs

Miembro Desde 02/16/16

361 Reputación

3 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

IUPUI, Team 3-2, Harley Spring 2016 Miembro de IUPUI, Team 3-2, Harley Spring 2016

IUPUI-HARLEY-S16S3G2

4 Miembros

3 Guías creadas

2 comentarios

The replacement battery I bought had contact strips that were too long and too wide for the slots on the circuit board, so I had to trim off about half the length and 1.5 mm of the width on each strip, but after that alteration, it worked fine.

Tom Hess - Contestar

What size is the Rechargeable Battery in the Norelco 5801XL .

Dave - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 13

Ultimos 30 días: 52

Todo El Tiempo: 4,011