Introducción

If your Olympus Stylus 410 no longer functions properly because of a faulty logic board, use this guide to install a new one.

Partes

No se requieren partes.

Locate the 2 screws on the bottom of the slider.
  • Locate the 2 screws on the bottom of the slider.

  • Remove both screws with a #00 Phillips screwdriver.

Agregar Comentario

Gently pull on the bottom of the slider until it comes off the lower track.
  • Gently pull on the bottom of the slider until it comes off the lower track.

  • There is a little piece that connects the slider to the track. Be sure not to lose this as it is needed to put the slider back on.

Agregar Comentario

Lift the slider up until it comes off the upper track.
  • Lift the slider up until it comes off the upper track.

Agregar Comentario

The slider should now be free from the body of the camera.
  • The slider should now be free from the body of the camera.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver. Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver. Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.
  • Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

Agregar Comentario

Use the spudger to peel off the outer metal band, starting from the bottom of the camera. The metal band it attached to the camera with glue in addition to screws.  Be careful not to bend the band when removing it from the camera.
  • Use the spudger to peel off the outer metal band, starting from the bottom of the camera.

  • The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

Agregar Comentario

The shutter button can now be removed. It is not connected to the camera and can be lifted off. The shutter button can now be removed. It is not connected to the camera and can be lifted off.
  • The shutter button can now be removed. It is not connected to the camera and can be lifted off.

Agregar Comentario

Remove the memory card. Locate and remove the 2 screws using a #00 Phillips screwdriver.
  • Remove the memory card.

  • Locate and remove the 2 screws using a #00 Phillips screwdriver.

Agregar Comentario

Use a spudger around the edge of the case to loosen it. Carefully wiggle the back case off. This may require a fair amount of force. Carefully wiggle the back case off. This may require a fair amount of force.
  • Use a spudger around the edge of the case to loosen it.

  • Carefully wiggle the back case off. This may require a fair amount of force.

Agregar Comentario

Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.
  • Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

Agregar Comentario

While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required. Be careful not to completely pull the front case off because it will still be connected with wires.
  • While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.

  • Be careful not to completely pull the front case off because it will still be connected with wires.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Rory Aronson

Miembro Desde 15/04/10

34 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 6-13, Maness Spring 2010 Miembro de Cal Poly, Team 6-13, Maness Spring 2010

CPSU-MANESS-S10S6G13

5 Miembros

9 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 2

Todo El Tiempo: 2,229