Introducción

This guide will instruct how to install the power supply.

Turn the device so that the bottom is facing up.
  • Turn the device so that the bottom is facing up.

Agregar Comentario

Use the plastic opening tool to carefully lift the rubber stops in each corner. Do not completely remove the rubber stops, because they are difficult to replace. Do not completely remove the rubber stops, because they are difficult to replace.
  • Use the plastic opening tool to carefully lift the rubber stops in each corner.

  • Do not completely remove the rubber stops, because they are difficult to replace.

Agregar Comentario

Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device. Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.
  • Unscrew the 4 11.8 mm T-8 Torx screws from each corner of the device.

Agregar Comentario

Lift the lower case straight up from the rest of the router. Lift the lower case straight up from the rest of the router.
  • Lift the lower case straight up from the rest of the router.

Agregar Comentario

Remove the clear plastic casing by lifting it straight up from the router. Remove the clear plastic casing by lifting it straight up from the router.
  • Remove the clear plastic casing by lifting it straight up from the router.

Agregar Comentario

Separate the motherboard from the top shell by lifting it straight up from the router. Separate the motherboard from the top shell by lifting it straight up from the router.
  • Separate the motherboard from the top shell by lifting it straight up from the router.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Turn the motherboard, so that the top is facing upwards.
  • Turn the motherboard, so that the top is facing upwards.

  • Place the motherboard on a clean flat surface.

Agregar Comentario

Remove the yellow tape that holds the wire. Make sure that you set the tape aside on a clean surface, so that it can be reused.
  • Remove the yellow tape that holds the wire.

  • Make sure that you set the tape aside on a clean surface, so that it can be reused.

Agregar Comentario

Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard. The wire should now be completely separate from the motherboard. The wire should now be completely separate from the motherboard.
  • Use tweezers to gently pull the metal bracket that connects the antenna to the motherboard.

  • The wire should now be completely separate from the motherboard.

Agregar Comentario

Extend the antenna away from the device, so that it becomes straight.
  • Extend the antenna away from the device, so that it becomes straight.

Agregar Comentario

Find the clips that hold the antenna onto the router. Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole. The antenna may take considerable force to remove.
  • Find the clips that hold the antenna onto the router.

  • Use one hand to push the clips in, while using your other hand to pull out the antenna. You may need to gently twist the antenna so it can separate from the hole.

  • The antenna may take considerable force to remove.

Agregar Comentario

Completely separate the antenna and wire from the rest of the device.
  • Completely separate the antenna and wire from the rest of the device.

Agregar Comentario

Unscrew the two 5 mm  Phillips Head screws located at the front corners of the motherboard.
  • Unscrew the two 5 mm Phillips Head screws located at the front corners of the motherboard.

Agregar Comentario

Take off the metal frame. Take off the metal frame.
  • Take off the metal frame.

Agregar Comentario

Turn over the motherboard, so that the bottom is facing up.
  • Turn over the motherboard, so that the bottom is facing up.

Agregar Comentario

Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes. Desolder the three connections between the reset button and the motherboard
  • Do not refer to the pictures in this step for correct soldering and de-soldering techniques. They are solely for illustration purposes.

  • Desolder the three connections between the reset button and the motherboard

  • For proper soldering and desoldering techniques, refer here.

  • Pull the power source from the other side of the mother board once the solder is liquid.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Nicole Slagle

Miembro Desde 25/01/13

77 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 3-31, Amido Winter 2013 Miembro de Cal Poly, Team 3-31, Amido Winter 2013

CPSU-AMIDO-W13S3G31

3 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 7

Todo El Tiempo: 1,389