Introducción

The keyboard has 3 main parts, including the speaker cover, the heat sink, and the keyboard itself. You have to remove these in order to remove the keyboard.

Partes

No se requieren partes.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Agregar Comentario

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Agregar Comentario

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Agregar Comentario

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

Agregar Comentario

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

Agregar Comentario

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Agregar Comentario

Locate the speaker cover.
  • Locate the speaker cover.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Contestar

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

Agregar Comentario

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

Agregar Comentario

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

Agregar Comentario

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

Agregar Comentario

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Contestar

That isn't the HDD!

Dix Dox - Contestar

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Agregar Comentario

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

Agregar Comentario

Remove the heatsink.
  • Remove the heatsink.

Agregar Comentario

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Agregar Comentario

Detach the ribbon cable.
  • Detach the ribbon cable.

Agregar Comentario

Remove the keyboard.
  • Remove the keyboard.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Sean Bent

Miembro Desde 01/04/11

41 Reputación

1 Guía escrita

Equipo

Cal Poly, Team 10-39, Forte Spring 2011 Miembro de Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 6

Todo El Tiempo: 1,818