Introducción

The following guide is to remove or replace the screen of the LG VX6000 cellphone.

Push the dark gray tab towards the top of the phone to release the battery.  The tab is located on the back of the phone.
  • Push the dark gray tab towards the top of the phone to release the battery. The tab is located on the back of the phone.

Remove battery

Ryan Brekke - Contestar

Remove battery pack.
  • Remove battery pack.

  • You will need to unhook the bottom of the battery pack from the slot.

Agregar Comentario

Set the battery aside.
  • Set the battery aside.

Agregar Comentario

Pull the two rubber cushions out using tweezers.
  • Pull the two rubber cushions out using tweezers.

  • Only remove the two cushions that are circled!

Agregar Comentario

Unscrew the six screws seen on the back using a Phillips 00 Screwdriver.
  • Unscrew the six screws seen on the back using a Phillips 00 Screwdriver.

  • Remove screws carefully on an uncluttered surface. They are very small and could get lost.

Agregar Comentario

Remove the back of the phone using your hands.
  • Remove the back of the phone using your hands.

  • There is a pair of red and blue wires that plugs into the motherboard. These wires will snap if you force the pieces apart.

  • Remove the back of the phone very gently. Use your fingernail or tweezers to unplug the wires.

  • To reattach the back, you must plug these wires back in.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Remove the metallic sticky tab on the top by peeling it off the metallic strip underneath.
  • Remove the metallic sticky tab on the top by peeling it off the metallic strip underneath.

Agregar Comentario

Pry and lift off the circuit connector, which is connected to the screen. Pry and lift off the circuit connector, which is connected to the screen.
  • Pry and lift off the circuit connector, which is connected to the screen.

Agregar Comentario

Lift the green motherboard up from the rest of the phone by pushing a corner away from the casing.
  • Lift the green motherboard up from the rest of the phone by pushing a corner away from the casing.

Agregar Comentario

Using a paper clip or tweezers, pop out the screen by pressing the plastic tab in the top-left corner of the phone's bottom casing. Be careful not to lose the tab that pops out.  It is a small and clear piece of plastic. The tab is fragile, handle with care.
  • Using a paper clip or tweezers, pop out the screen by pressing the plastic tab in the top-left corner of the phone's bottom casing.

  • Be careful not to lose the tab that pops out. It is a small and clear piece of plastic.

  • The tab is fragile, handle with care.

Agregar Comentario

As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated. As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated. As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.
  • As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.

Agregar Comentario

Set the bottom half of the phone aside.
  • Set the bottom half of the phone aside.

  • Using tweezers pull off the rubber and cushions and sticker cushions at the four corners of the screen.

Agregar Comentario

With a Phillips tip screwdriver, unscrew the four newly exposed screws.
  • With a Phillips tip screwdriver, unscrew the four newly exposed screws.

  • Set the screws aside so as not to lose them.

Agregar Comentario

Using the iFixit plastic opening tool, carefully pry open the front casing from the side. Open the casing  by prying each side a little bit at a time.  Rotate and open until all the clips pop open and the casing opens up. Open the casing  by prying each side a little bit at a time.  Rotate and open until all the clips pop open and the casing opens up.
  • Using the iFixit plastic opening tool, carefully pry open the front casing from the side.

  • Open the casing by prying each side a little bit at a time. Rotate and open until all the clips pop open and the casing opens up.

Agregar Comentario

After you pry open the casing, you will be left with the screen and circuit board in the top face plate. Gently  pull the corner of screen and circuit board up and out of casing to remove screen from the top face plate.
  • After you pry open the casing, you will be left with the screen and circuit board in the top face plate.

  • Gently pull the corner of screen and circuit board up and out of casing to remove screen from the top face plate.

  • Do not try to completely separate the circuit board from the casing. There are still wires connecting the two.

Agregar Comentario

Carefully peel the sticky tape that connects the screen and logic board off. The screen can now be removed.
  • Carefully peel the sticky tape that connects the screen and logic board off. The screen can now be removed.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Adam Altman

Miembro Desde 14/01/10

1 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 4-11, Forte Winter 2010 Miembro de Cal Poly, Team 4-11, Forte Winter 2010

CPSU-FORTE-W10S4G11

5 Miembros

10 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 7

Todo El Tiempo: 2,488