Introducción

Instructions to get to and remove the keypad unit.

Turn the phone on its back. Turn the phone on its back.
  • Turn the phone on its back.

Agregar Comentario

Orient the phone as shown. Remove the battery cover by pushing upward with your thumb.
  • Orient the phone as shown.

  • Remove the battery cover by pushing upward with your thumb.

Agregar Comentario

Place your fingernail at the top of the battery and pry the battery out towards you. Place your fingernail at the top of the battery and pry the battery out towards you.
  • Place your fingernail at the top of the battery and pry the battery out towards you.

Agregar Comentario

Orient the phone as shown with the battery already removed.
  • Orient the phone as shown with the battery already removed.

Agregar Comentario

Remove the 2 plastic plugs located on the side and upper quadrant of the rear body panel by using the push-pin and lifting outwards. Use a Phillips #00 screwdriver to remove the 5 screws as shown here. Use a Phillips #00 screwdriver to remove the 5 screws as shown here.
  • Remove the 2 plastic plugs located on the side and upper quadrant of the rear body panel by using the push-pin and lifting outwards.

  • Use a Phillips #00 screwdriver to remove the 5 screws as shown here.

Agregar Comentario

Place an iPod opener tool in the seam above the antenna. Run the tool around the perimeter of the entire phone. Run the tool around the perimeter of the entire phone.
  • Place an iPod opener tool in the seam above the antenna.

  • Run the tool around the perimeter of the entire phone.

Agregar Comentario

Check to see that your device looks like the attached photo.
  • Check to see that your device looks like the attached photo.

Agregar Comentario

Locate the tabs that hold the logic board in place. Pull the outer frame of the phone outwards to release the board from the tabs. Pull the outer frame of the phone outwards to release the board from the tabs.
  • Locate the tabs that hold the logic board in place.

  • Pull the outer frame of the phone outwards to release the board from the tabs.

Agregar Comentario

Locate the copper connection (orange-colored) on the back of the board. Pry the connector free from the board with your fingernail. Pry the connector free from the board with your fingernail.
  • Locate the copper connection (orange-colored) on the back of the board.

  • Pry the connector free from the board with your fingernail.

Agregar Comentario

Check to see that your device looks like the image shown.
  • Check to see that your device looks like the image shown.

  • Note: The image is shown with the LCD screen removed. This is not necessary for logic board removal.

Agregar Comentario

Use your finger to lift up the keypad. Use your finger to lift up the keypad. Use your finger to lift up the keypad.
  • Use your finger to lift up the keypad.

Agregar Comentario

Check to see that your device looks like the image shown.
  • Check to see that your device looks like the image shown.

  • Do not let the buttons fall out of the side casing of the phone!

  • Note: The image is shown with the LCD screen removed. This is not necessary for keypad repair.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Douglas Blaalid

Miembro Desde 13/01/10

282 Reputación

15 Guías creadas

Equipo

Cal Poly, Team 4-13, Forte Winter 2010 Miembro de Cal Poly, Team 4-13, Forte Winter 2010

CPSU-FORTE-W10S4G13

5 Miembros

15 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 1,768